OPB916BOCZ

OPB916 Series Features: Low power consumption Data rates to 250 kBaud Choice of two logic states and two electrical outputs 24 (610 mm) minimum 26 AWG UL listed wires Slot width 0.20 (5.08 mm) Slot Depth 0.635 (16.13 mm) Description: The OPB916 series of Photologic photo integrated circuit switches provide optimum flexibility. Each switch consists of an infrared Light Emitting Diode (LED) and a Photologic photo integrated circuit, mounted in an opaque housing with clear windows for dust protection. The deep slot allows for a longer reach of the optical path from the 0.650 (16.5 mm) mounting plane. Internal apertures are 0.010 x .060 (.25 mm x 1.52 mm) for the Photologics S side and 0.05 x 0.06 (1.27 mm x 1.52 mm) for the LED E side. Devices in this series exhibit stable performance over supply voltages ranging from 4.5 V to 16.0 V, and may be specified as bueff red or inverted with an internal 10 k pull -up resistor or open collector output. Devices are TTL/LSTTL compatible and can drive up to 10 TTL loads. Custom electrical, wire or cabling are available. Contact your local representative or OPTEK for more information. Ordering Information Applications: LED Slot Aperture Lead Mechanical switch replacement Part Peak Sensor Width / Emiett r / Length / Speed indication (tachometer) Number Wavelength Photologic Depth Sensor Wire Mechanical limit indication OPB916BZ 10K Pull-Up Edge sensing 0.200 / 0.05 / 24 / 26 OPB916IZ 880 nm Inv-10K Pull-Up 0.635 0.01 AWG Wire OPB916BOCZ Open-Collector OPB916B 10K Pull-Up OPB916BOC Open-Collector Light ON Color Description output High Red Anode Light ON output High Black Cathode White Vcc Blue Output OPB916I Inverted 10K Pull-Up OPB916IOC Inverted Open-Collector Green Ground Light ON output Low Light ON output Low Ro HS General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specificaoti n without 1645 Wallace Drive, Carrollton, TX 75006 Ph: +1 972 323 2200 nocti e or liability. All informaoti n is subject to TT Electronics own data and is www.optekinc.com www.ttelectronics.com considered accurate at time of going to print. Issue B 10/2016 Page 1 TT electronics plc Color-Pin Description Red Anode Black Cathode Green Ground Blue Output White V CC Tolerence 0.010 0.254 MILLIMETERS DIMENSIONS ARE IN: INCHES Absolute Maximum Ratings (T = 25 C unless otherwise noted) A Storage & Operating Temperature Range -40C to +80C Input Infrared LED Diode Reverse DC Voltage 2 V (2) Input Diode Power Dissipation 75 mW Forward DC Current 50 mA Output Photologic Supply Voltage, V (not to exceed 3 seconds) 18 V CC Voltage at Output Lead (Open Collector Output) 30 V (3) Output Photologic Power Dissipation 90 mW Notes: (1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (2) Derate linearly 1.67 mW/C above 25. (3) Derate linearly 2.67 mW/C above 25. (4) Normal application would be with light source blocked, simulated by I = 0 mA. F (5) All parameters tested using pulse technique. General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specificaoti n without 1645 Wallace Drive, Carrollton, TX 75006 Ph: +1 972 323 2200 nocti e or liability. All informaoti n is subject to TT Electronics own data and is www.optekinc.com www.ttelectronics.com considered accurate at time of going to print. Issue B 10/2016 Page 2 TT electronics plc