OPB917IOCZ

Photologic Slotted Optical Switch OPB917 Series Features: Low power consumption Data rates to 250 kBaud Choice of two logic states and two electrical outputs 24 (610 mm) minimum 26 AWG UL listed wires Slot width 0.20 (5.08 mm) Slot Depth 0.86 (21.84 mm) Description: The OPB917 series of Photologic photo integrated circuit switches provide optimum flexibility. Each switch consists of an infrared Light Emitting Diode (LED) and a Photologic photo integrated circuit, mounted in an opaque housing with clear windows for dust protection. The deep slot allows for a longer reach of the optical path from the 0.650 (16.5 mm) mounting plane. Internal apertures are 0.010 x .060 (.25 mm x 1.52 mm) for the Photologics S side and 0.05 x 0.06 (1.27 mm x 1.52 mm) for the LED E side. Devices in this series exhibit stable performance over supply voltages ranging from 4.5 V to 16.0 V, and may be specified as buffered or inverted with an internal 10 k pull-up resistor or open collector output. Devices are TTL/ LSTTL compatible and can drive up to 10 TTL loads. Custom electrical, wire or cabling are available. Contact your local representative or OPTEK for more information. Applications: Ordering Information Mechanical switch replacement Aperture Slot Width/ Lead Length / Part LED Peak Sensor Emitter/ Speed indication (tachometer) Depth Wire Number Wavelength Photologic Sensor Mechanical limit indication OPB917BZ 10K Pull-Up Edge sensing OPB917IZ Inv-10K Pull-Up 0.200 / 24 / 26 AWG 880 nm 0.05 / 0.01 OPB917BOCZ Open-Collector 0.635 Wire OPB917IOCZ Inv-Open-Collector OPB917BZ 10K Pull-Up OPB917BOCZ Open-Collector Color Description Light ON Red Anode output High Black Cathode Light ON output High White Vcc Blue Output Green Ground OPB917IZ Inverted 10K Pull-Up OPB917IOCZ Inverted Open-Collector Light ON output Low Light ON output Low OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. RoHS OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Issue C 01/2015 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors optekinc.com www.optekinc.com Page 1 of 4 Photologic Slotted Optical Switch OPB917 Series Color Description Red Anode Black Cathode Green Ground Blue Output White V CC MILLIMETERS DIMENSIONS ARE IN: INCHES Absolute Maximum Ratings (T =25C unless otherwise noted) A Storage & Operating Temperature Range -40C to +80C (1) Lead Soldering Temperature 1/16 inch (1.6mm) from the case for 5 sec. with soldering iron 260C Input Infrared LED Supply Voltage, V (not to exceed 3 seconds) 18 V CC (2) Input Diode Power Dissipation 100 mW Forward DC Current 50 mA Output Photologic Voltage at Output Lead (Open Collector Output) 35 V Diode Reverse DC Voltage 2 V (3) Output Photologic Power Dissipation 90 mW Notes: (1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (2) Derate linearly 1.33 mW/C above 25. (3) Derate linearly 2.50 mW/C above 25. (4) Normal application would be with light source blocked, simulated by I = 0 mA. F (5) All parameters tested using pulse technique. OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue C 01/2015 OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Page 2 of 4 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors optekinc.com www.optekinc.com