OPB608B

Sensing and Control Reflective Object Sensor OPB608A, OPB608B, OPB608C, OPB608R, OPB608V Features: Phototransistor output Unfocused for sensing di use surface Low cost plas c housing Enhanced signal to noise ra o Reduced ambient light sensi vity Descrip on: OPB608 reec ve switches consist of an infrared emi ng device (LED or VCSEL) and a NPN silicon phototransistor mounted side- by-side on a parallel axis in a black opaque plas c housing. All OPB608s (except OPB608R) have an emi ng device and a phototransistor that are encapsulated in a visible ltering epoxy. The phototransistor responds to radiaon from the emi er only when a reec ve object passes within its eld of view. The phototransistor has enhanced low current roll-o to improve the contrast ra o and immunity to background irradiance. LED versions are designed for near- eld applica ons. The VCSEL version is designed for longer distances. OPB608A, OPB608B and OPB608C devices are designed for applica ons with reec ve distances between 0.050 (1.270 mm) and 0.375 (9.525 mm). OPB608V is designed for applica ons with re ec ve distances between 0.050 (1.270 mm) and 1.200 (30.480 mm). All of these are designed for light pa erns not visible to the human eye. By ulizin g the night enhancement funcon of a camera, the near infrared light pa ern can be seen. This allows a user to see the pa ern shining on the reec ve object. OPB608R is designed for applica ons with re ec ve distances between 0.050 (1.270 mm) and 0.300 (7.620 mm). It is designed for light pa erns visible to the human eye. The eciency of this sensor is lower for opcal wavelengths in the visible range, thus reducing the distance that can be used. Reec ve distances are depen dent upon the drive current for the light emi ng device, the wavelength of the light source, and the type of reec ve material therefore, each applica on should be checked for the ability to meet each requirement. Custom electrical, wire and cabling and connectors are available. Contact your local representave or OPTEK for more informa on. Ordering Informa on Applica ons: Part LED Peak Reec on Distance Lead Non-contact reec ve object sensor Number Wavelength Sensor Inch (mm) Length Assembly line automa on OPB608A Machine automa on 890 nm OPB608B Machine safety See Graph 0.18 OPB608C Rbe Transistor End of travel sensor on Page 4 (Min) OPB608R 650 nm Door sensor OPB608V 850 nm Addi onal laser safety informa on can be found on the Optek website. See applica on 221. Classica on is not marked on the device due to space limita ons. See package outline for centerline of op cal radiance. Opera ng devices beyond maximum ra ng may cause devices to exceed rated classica on General Note TT Electronics reserves the right to make changes in product specica on 1645 Wallace Drive, Carrollton, TX 75006 Ph: +1 972 323 2200 without no ce or liability. All informa on is subject to TT Electronics own data www.optekinc.com www. electronics.com and is considered accurate at me of going to print. Issue D 05/2015 Page 1 TT electronics plc Sensing and Control Reflective Object Sensor OPB608A, OPB608B, OPB608C, OPB608R, OPB608V Absolute Maximum Ra ngs (T =25C unless otherwise noted) A Storage Temperature Range -40 C to +85 C Opera ng Temperature Range OPB608 A, B, C & R -40 C to +85 C OPB608V 0 C to +70 C (1) Lead Soldering Temperature 1/16 inch (1.6mm) from the case for 5 sec. with soldering iron 260 C Total Power Dissipa on 100 mW OPB608A, OPB608B, OPB608C (Infrared-LED 890 nm) Forward DC Current 50 mA Peak Forward Current (1 s pulse width, 300 pps) 3 A Reverse DC Voltage 2 V OPB608R (Visible Red-LED 650 nm) Forward DC Current 50 mA Reverse DC Voltage 5 V OPB608V (Infrared-VCSEL 850 nm) Forward DC Current 12 mA Reverse DC Voltage 5 V Phototransistor Collector-Emi er Voltage 30 V Emi er Reverse Current 10 mA Collector DC Current 25 mA Notes: (1) RMA ux is recommended. Dura on can be extended to 10 seconds maximum when ow soldering. (2) Methanol or isopropanol are recommended as cleaning agents. The plas c housing is soluble in chlorinated hydrocarbons and keytones. Pin LED Pin Transistor 4 Cathode 1 Collector 3 Anode 2 Emi er 4 1 3 2 MILLIMETERS DIMENSIONS ARE IN: INCHES General Note TT Electronics reserves the right to make changes in product specica on 1645 Wallace Drive, Carrollton, TX 75006 Ph: +1 972 323 2200 without no ce or liability. All informa on is subject to TT Electronics own data www.optekinc.com www. electronics.com and is considered accurate at me of going to print. Issue D 05/2015 Page 2 TT electronics plc