MP3307 2.7V-5.5V Input, 24V OVP, Programmable Fsw, White LED Driver The Future of Analog IC Technology FEATURES DESCRIPTION 2.7V to 5.5V Input Voltage The MP3307 is a non-synchronous WLED step- Analog Dimming with >20kHz Input Signal up driver with a 2.7V to 5.5V input range. It Direct PWM Dimming Mode with 100Hz to uses peak current mode to regulate the LED current sensed through an external low-side 2kHz Input Signal resistor. Up to 2.2MHz Programmable Switching Frequency The MP3307 features up to 2.2MHz of Low 200mV Feedback Voltage with 1% programmable switching frequency, making it Accuracy at Room Temperature easy to avoid noise interference, optimize 24V Open-Load Protection Threshold efficiency, and reduce the output filter UVLO and Thermal Shutdown component size. To extend the dimming range, Cycle-by-Cycle Over-Current Protection both analog and PWM dimming modes are Available in a TSOT23-8 Package supported with a separate input. The MP3307 has LED open protection, output APPLICATIONS over-voltage protection, cycle-by-cycle current- Video Displays limit protection, and thermal shutdown In-Car LCD Infotainment protection. Tablets The MP3307 is available in a TSOT23-8 All MPS parts are lead-free, halogen-free, and adhere to the RoHS directive. For package, which is ideal for use in video displays. MPS green status, please visit the MPS website under Quality Assurance. MPS and The Future of Analog IC Technology are registered trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION 95 Effi Boost 90 85 Effi LEDs 80 75 70 65 60 55 50 23 4 5 6 MP3307 Rev.1.0 www.MonolithicPower.com 1 8/25/2015 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2015 MPS. All Rights Reserved. MP33072.7V-5.5V INPUT, 24V OVP, PROGRAMMABLE F , WHITE LED DRIVER SW ORDERING INFORMATION Part Number* Package Top Marking MP3307GJ TSOT23-8 See Below * For Tape & Reel, add suffix Z (e.g. MP3307GJZ) TOP MARKING ANF: Product code of MP3307GJ Y: Year code PACKAGE REFERENCE TOP VIEW TSOT23-8 (1) (4) ABSOLUTE MAXIMUM RATINGS Thermal Resistance JA JC V ...................................................-0.3V to +6V TSOT23-8.............................100......55 C/W IN V , V ..-1V to +40V SW OUT NOTES: All other pins ..................................0.3V to +6V 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the Junction temperature ................................150C maximum junction temperature T (MAX), the junction-to- J Lead temperature .....................................260C ambient thermal resistance , and the ambient temperature JA (2) T . The maximum allowable continuous power dissipation at A Continuous power dissipation .....(T = 25C) A any ambient temperature is calculated by P (MAX) = (T D J TSOT23-8 ................................................ 1.25W (MAX)-T )/ . Exceeding the maximum allowable power A JA dissipation will cause an excessive die temperature, causing (3) Recommended Operating Conditions the regulator to go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent Supply voltage (V ) ........................2.7V to 5.5V IN damage. Operating junction temp. (T )... -40C to +125C J 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD51-7, 4-layer PCB. MP3307 Rev.1.0 www.MonolithicPower.com 2 8/25/2015 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2015 MPS. All Rights Reserved.