63892-7370

Mini-Mac Applicator for Standard .093 Pin and Socket Crimp Terminal Mini-Mac Applicator Application Tooling Specification Sheet Order No. 63892-7300 FEATURES Directly adapts to most automatic wire processing machines Applicator designed to industry standard mounting and shut height 135.80mm (5.346 ) Quick set-up time plus the crimp height, track and feed adjustments can be set without removing the applicator from the press Fine adjustment allows users to achieve target with little effort by adjusting in increments of .015mm (.0006 ) for conductor crimp height and .063mm (.0025 ) for insulation height Independent adjustment rings allow users to quickly adjust the conductor or insulation crimp height without affecting each other. SCOPE Products: 2.36mm (.093 ) Diameter, Standard .093 Pin and Socket Crimp Terminal, 14-20 AWG. Wire Size Insulation Diameter Strip Length Terminal Terminal Order No. Series No. AWG mm mm In. mm In. 02-09-1101 02-09-5102 39-00-0290 02-09-1102 39-00-0071 39-00-0292 02-09-3101 39-00-0135 39-00-0293 14-20 2.00-0.50 1.65-4.06 .065-.160 3.96-5.54 .156-.218 02-09-3103 39-00-0281 50-29-1617 02-09-5100 39-00-0282 1189 02-09-1101 02-09-5102 39-00-0290 02-09-1102 39-00-0071 39-00-0292 02-09-3101 39-00-0135 39-00-0293 18 DBL. 0.80 (2) 1.65-4.06 .065-.160 3.96-5.54 .156-.218 02-09-3103 39-00-0281 50-29-1617 02-09-5100 39-00-0282 02-09-2101 02-09-6101 39-00-0298 02-09-4101 39-00-0105 39-00-0300 14-20 2.00-0.50 1.65-4.06 .065-.160 3.96-5.54 .156-.218 02-09-6100 39-00-0296 1190 02-09-2101 02-09-6101 39-00-0298 02-09-4101 39-00-0105 39-00-0300 18 DBL. 0.80 (2) 1.65-4.06 .065-.160 3.96-5.54 .156-.218 02-09-6100 39-00-0296 1450 02-09-2301 02-09-2302 02-09-2306 14-20 2.00-0.50 1.65-4.06 .065-.160 3.96-5.54 .156-.218 1451 02-09-1301 02-09-1302 14-20 2.00-0.50 1.65-4.06 .065-.160 3.96-5.54 .156-.218 02-09-8108 14-18 2.00-0.80 1.65-4.06 .065-.160 3.96-5.54 .156-.218 1973-2 02-09-8108 18 DBL. 0.80 (2) 1.65-4.06 .065-.160 3.96-5.54 .156-.218 4550 02-09-1205 02-09-5169 50-29-1618 14-20 2.00-0.50 1.65-4.06 .065-.160 3.96-5.54 .156-.218 6310 02-09-1209 02-09-5205 14-20 2.00-0.50 1.65-4.06 .065-.160 3.96-5.54 .156-.218 The above application does not conform to the current product specification. This applicator is for 2.54-4.06 (.100-.160) insulation diameters and double crimp applications. See applicator 63892-7100 for 1.65-2.79 (.065-.110) insulation diameters. Doc No.ATS-638927300 Release Date: 02-16-07 UNCONTROLLED COPY Page 1 of 6 Revision: C Revision Date: 05-14-12 Mini-Mac Applicator for Standard .093 Pin and Socket Crimp Terminal DEFINITION OF TERMS C/L TERMINAL LOCATION BEND UP BELL MOUTH ROLLING BRUSH SEAM INSULATION CRIMP CUT-OFF TAB TWISTING BEND STRIP DOWN LENGTH CONDUCTOR C/L CRIMP HEIGHT CRIMP Terminal is to be centrally located between the two (2) cut-off tab edges by one half of the total cut-off tab tolerance. This illustration is a generic terminal representation and not an exact image of any terminal listed in the scope. CRIMP SPECIFICATIONS Bell mouth Cut-off Tab Conductor Brush Terminal Series No. mm In. mm In. mm In. 1189 3.53-3.69 .139-.145 1190 3.53-3.69 .139-.145 1450 3.53-3.69 .139-.145 1451 3.53-3.69 .139-.145 1973-2 3.53-3.69 .139-.145 4550 3.53-3.69 .139-.145 6310 3.53-3.69 .139-.145 Punch Width (Ref) Bend up Bend down Twist Roll Terminal Series No. Conductor Insulation Degree Degree mm In. mm In. Seam 1189 2.30 .091 3.85 .151 1190 2.30 .091 3.85 .151 Seam shall not be open 1450 2.30 .091 3.85 .151 and no wire allowed out 1451 2.30 .091 3.85 .151 of the crimping area 1973-2 2.30 .091 3.85 .151 4550 2.30 .091 3.85 .151 6310 2.30 .091 3.85 .151 NOTE: Some of the specifications in these charts above are intentionally left blank due to the fact that the information does not currently exist. Doc No.ATS-638927300 Release Date: 02-16-07 UNCONTROLLED COPY Page 2 of 6 Revision: C Revision Date: 05-14-12