Dimensions: mm Recommended Land Pattern: mm Electrical Properties: Properties Test conditions Value Unit Tol. Capacitance C 1 0.2 V , 1 kHz 10% 25 C 220 pF 10% RMS Rated Voltage U 50 V (DC) max. R pl1 Dissipation DF 1 0.2 V , 1 kHz 10% 25 C 2.5 % max. Factor pl2 RMS Insulation Fl R Apply U for 120 s max. 10 G min. Resistance ISO R Precondition for Class II MLCC measurement: Apply a preheat treatment 150 10 C for 1 hour. The measurement should be applied after 24 2 hrs the part was stored under ambient conditions. There is not any precondition necessary for Class I MLCC. L Schematic: General Information: General Purpose MLCC Ceramic Type X7R Class II Temperature Coefficient 15 % max. Storage Conditions (in original 5-35 C, < 75% RH packaging) Operating Temperature -55 up to +125 C Dielectric Strength 5 sec. 250 % U Charge & Discharge Current <50 mA R FIT according to separate documentation Component conform to REACh and RoHS requirements and standards Properties Value Unit Tol. Length L 1.6 mm 0.2 CREATED CHECKED GENERAL TOLERANCE PROJECTION Wrth Elektronik eiSos GmbH & Co. KG METHOD Width W 0.8 mm 0.1 EMC & Inductive Solutions KaS PSL DIN ISO 2768-1m Max-Eyth-Str. 1 Height H 0.8 mm 0.07 74638 Waldenburg DESCRIPTION TECHNICAL REFERENCE Germany Pad Dimension Fl 0.4 mm 0.15 X7R0603221K050DFCT1S000 Tel. +49 (0) 79 42 945 - 0 WCAP-CSST Soft Termination www.we-online.com ORDER CODE pl1 - Reflow 2.3 mm pl2 - Reflow 0.7 mm fw - Reflow 0.8 mm eiSos we-online.com MLCC pl1 - Wave 2.4 mm pl2 - Wave 1 mm fw - Wave 0.8 mm 885382206001 SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE 001.000 Valid 2018-11-12 eiCap 1/7 0603 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Wrth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Wrth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. W H fwMechanical Properties: Substrate Bending Test: The capacitor shall be soldered on the test substrate (see Figure) and gradually bent to a depth, D with a speed Properties Definition of 1,0 mm/s 0,5 mm/s. Adhesive Flexure(D): 5mm Strength of 0402 & 0603 10 1 sec 5 N Pressure maintaining: 5 1 sec. Termination > 0603 10 1 sec 10 N Vibration all 3 directions, 2 hours each 10 - 55 Hz/ min., amplitude 0.75 mm Resistance or 10 g Resistance to Specific Refer to Soldering Profile Solder Heat Substrate all 5 1 sec 5 mm bending test This substrate bending test is for all size of WCAP-CSST. CREATED CHECKED GENERAL TOLERANCE PROJECTION Wrth Elektronik eiSos GmbH & Co. KG METHOD EMC & Inductive Solutions KaS PSL DIN ISO 2768-1m Max-Eyth-Str. 1 74638 Waldenburg DESCRIPTION TECHNICAL REFERENCE Germany X7R0603221K050DFCT1S000 Tel. +49 (0) 79 42 945 - 0 WCAP-CSST Soft Termination www.we-online.com ORDER CODE eiSos we-online.com MLCC 885382206001 SIZE REVISION STATUS DATE (YYYY-MM-DD) BUSINESS UNIT PAGE 001.000 Valid 2018-11-12 eiCap 2/7 0603 This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Wrth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Wrth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.