70 117224

WHITE-RODGERS DC PRODUCTS Type 70 and 71 contactors FEATURES High current capacity control Isolated or grounded coils Enclosed in dust-resistant case Longer steel encasement per mits lower heat r ise and more sensitive operation on Type 71 GENERAL DATA ENGINEERING DATA Dielectr ic Strength Contacts 500 Volts Pole for m SPNO, SPDT Temperature Range Mater ial SPNO-copper or silver -40F/-40C to 122F/50C SPDT-copper and silver or all silver Mechanical Life (no load) 5 Ter mination / -24 UNF-2A thread 16 250,000 operations Electr ical Life (rated load) RATINGS NO NC 100,000 operations Type Volts DC Cont. Inrush Cont. Inrush Mounting Position 6 80A 300 A 60A 100 A Recommended mounting with cap down 70 12 80 A 150 A 60 A 60 A Vibration 24 & 36 50 A 50 A 30 A 30 A 5 gs ver tical and hor izontal planes 6 80A 300 A 60A 100 A 71 12 80 A 150 A 60 A 60 A Weight (approximate) 24 & 36 50 A 50 A 30 A 30 A Type 7014.0 oz. Type 7117.0 oz. Coils Duty Cycle Voltage6 VDC through 36 VDC Continuous Ter mination 10-32 UNF-2A thread Inter mittent10 seconds on maximum and Power (approximate) minimum 60 seconds off . One minute on Type 70 inter mittent 23 watts maximum and minimum 6 minutes off . Type 70 continuous 9 watts Hardware Torque Specification Type 71 inter mittent 25 watts Contact Ter minal: 45-55 inch-lbs. Type 71 continuous 10 watts Coil Ter minal: 12-18 inch-lbs. Connections Mounting Bracket: 100 inch-lbs. max (a 1. Two coil ter minals isolated from case backup wrench must be used to hold the 2. One coil ter minal with ground wire, one coil bottom nut stationar y dur ing installation) ter minal isolated from case 3. One coil lead common to NO ter minal mar ked BAT (one ter minal) Operate (77F/25C) 75% of nominal coil voltage 110% max. safe of COIL DATA nominal coil voltage TYPE 70 TYPE 71 Resistance (Ohms) Resistance (Ohms) Int. Cont. Int. Cont. Volts DC Volts DC 1.5 4.0 1.4 3.5 6 6 6.2 16.0 4.9 13.5 12 12 16.0 37.4 13.46 36.0 18 18 23.9 60.4 20.1 57.1 24 24 60.4 114.0 57.1 131.0 36 36 St. Louis, Missour i Mar kham, Ontar io 314-553-3600 905-948-3411 The Emerson logo is a R-4003C trademark and a service mark www.white-rodgers.com of Emerson Electric Co. 1233BAT TYPE 70/71 PART NUMBERING SYSTEM 7x x xx x x x - x Coil Termination Factory Assigned Specials Basic Part (15 in-lb torque spec.) Coil (where undefined, contact factory) Number Series Voltage/Duty 221 Isolated coil, all Ag contacts 2 Hardware loosely Type 71 case is 222 Coil terminal with ground 08 6 Volt continuous assembled approx. 0.29 longer wire, all Ag contacts 09 6 Volt intermittent 2B Customer requested than Type 70 224 Isolated coil, Cu NO 11 12 Volt continuous markings and Ag NC contacts 12 12 Volt intermittent 2C Customer requested 225 Coil terminal with ground 14 18 Volt continuous markings Contact wire, Cu NO and Ag NC 15 18 Volt intermittent 3 Customer requested Form contacts 17 24 Volt continuous markings 226 Coil common to NO (stud 18 24 Volt intermittent 4 Customer requested 1 SPNO marked BAT), Cu NO 20 36 Volt continuous markings 3 SPDT and Ag NC contacts 21 36 Volt intermittent 5 Hardware bulk packed 5C Customer requested Not all par t number combinations are released. Please contact your Sales Representative for markings 5F Customer requested a list of active par t numbers. markings 7 No hardware included APPLICATION NOTES A back-up wrench MUST be used to hold the bottom nut stationar y dur ing installation. Solenoids applied in batter y charging circuits should be protected from higher than rated voltage dur ing charging. The ser vice life may be affected by this condition and the solenoid may or may not operate the circuit as intended. Circuits should be designed to provide safe operation should the solenoid fail in either the open or closed position. Special constr uction options, including a cur ved bracket, may be available under other par t numbers, including 111- xxxD (shor t can), 111-xxxE (long can), 5608-x and 878x-x. SPNO Isolated Coil Coil Terminal to Ground 5/16UNF2A 5/16UNF2A .485 (USABLE) .485 (USABLE) .281 WIDE X .390 LONG SLOT .281 WIDE X .390 LONG SLOT LENGTH LENGTH 10-32 UNF-2A X .470 GROUND COIL CONNECTION WIRE (ISOLATED) 2.109 2.109 W 3.480 COIL CONNECTION W 3.480 WITH GROUND WIRE 10-32 UNF-2A X .470 .248 .248 0.900 0.900 (Type 70) (Type 70) .569 1.082 .569 1.082 1.196 1.196 H (Type 71) H (Type 71) 2.400 2.400 L L 2.429 (Type 70) 2.429 (Type 70) 2.725 (Type 71) 2.725 (Type 71) CIRCUIT DIAGRAM CIRCUIT DIAGRAM Coil Common to Load SPDT Isolated Coil 5/16UNF2A 5/16UNF2A .485 (USABLE) .281 WIDE X .390 LONG SLOT .485 (USABLE) .281 WIDE X .390 LONG SLOT LENGTH LENGTH COMMON TERMINAL .248 W COIL CONNECTION 1032 UNF2A 2.109 3.480 .470 LONG W 3.480 (COMMON) 2.109 1032 UNF2A .470 LONG 0.900 .248 1.082 COIL CONNECTION (Type 70) .569 0.900 (COMMON) H 1.082 (Type 70) .569 1.196 2.400 (Type 71) 1.196 H L (Type 71) 2.400 3.313 (Type 70) L 3.609 (Type 71) 2.429 (Type 70) 2.725 (Type 71) CIRCUIT DIAGRAM CIRCUIT DIAGRAM R-4003C 1233