586 108111

Type 586 DC Power Contactor Water resistant Double-make or double-break contacts Capable of handling high and low current requirements Impact resistant phenolic casing Contacts SPECIFICATIONS Pole form: SPNO and SPDT Dielectric Strength Material: silver alloy 500 volts Termination: 5/16- 24 UNF-2A thread Temperature Range CONTACT RATINGS -40F/-40C to 149F/65C Normally open Normally closed Mechanical Life (no load) Volts DC Continuous Inrush Continuous Inrush 100,000 operations 6 200A 600A 100A 300A 12 200A 600A 100A 300A Electrical Life (rated loadmaking and breaking 200 amp on NO contacts) 24 & 36 200A 600A 100A 300A 50,000 cycles Coils Mounting Position Voltage: 6 V through 48VDC Recommended mounting is vertical plane with coil Termination: 10-32 UNF-2A thread terminals up Power (approximate) Weight (approximate) Continuous: 12 watts SPDT, SPNO: 24.0 oz. 8 watts SPNO SPDT: 26.0 oz. Connections Duty Cycle Coil isolated (two terminals) Continuous Minimum operating voltage Intermittent: 10 seconds on maximum and minimum 75% of rated coil voltage 60 seconds off. Maximum 10% over rated coil voltage One minute on maximum and minimum 6 minutes off Hardware Torque Specicfi ation COIL DATA Contact Terminal: 60 inch-lbs. max. Resistance in Ohms Coil Terminal: 12-18 inch-lbs Intermittent* Continuous Volts DC SPDT SPNO SPDT SPNO 6 2.2 3.3 3.3 5.25 12 8.4 13.2 13.2 21.0 15 13.1 21.0 21.0 32.8 24 18.4 30.0 30.0 47.0 28 33.6 53.0 53.0 84.0 36 75.6 120.0 120.0 189.0 48 134.0 213.0 213.0 336.0 *Intermittentspecial request onlyType 586 DC Power Contactor APPLICATION NOTES Not all part number combinations are available. Please contact Circuits should be designed to provide safe operation should the your Sales Representative for available part numbers. DC contactor fail in either the open or closed position. DC contactor applied in battery charging circuits should be protected from higher than rated voltage during charging. The service life may be affected by this condition and the DC contactor may or may not operate the circuit as intended. SPDT: ISOLATED COIL .281 WIDE X .640 LONG SLOT .594 NORMALLY OPEN 10-32 UNF-2A X .375 LONG W 3.300 H 2.797 NORMALLY 1.156 CLOSED 2.300 1.274 CIRCUIT DIAGRAM 5/16-24 1.375 UNF-2A X .594 LONG L 4.618 SPNO: ISOLATED COIL .281 WIDE X .640 LONG SLOT NORMALLY .594 10-32 OPEN UNF-2A X .375 LONG W 3.300 H 2.797 1.156 2.300 1.274 CIRCUIT DIAGRAM 5/16-24 UNF-2A X .594 LONG 1.375 L 3.688 TYPE 586 Part Numbering System Series Part Number 586 X X X X X X - X Contact Form Coil Voltage/Duty Coil Termination Contact Material Mounting Bracket Factory Assigned Specials (where undefined, contact factory) 1SPNO 026 Volt continuous 1Isolated 1AgCdO 1Standard bracket 3SPDT 0512 Volt continuous No dashStandard assembly, hardware sent bulk 0815 Volt continuous 2Extra hardware loosely mounted 1424 Volt continuous 6Customer requested markings 1628 Volt continuous 6ACustomer requested markings 1736 Volt continuous 2048 Volt continuous R-4762 2018 Emerson Electric Co. White-Rodgers and Emerson are trademarks of Emerson Electric Co. All rights reserved emerson.com