93026-45MS

DSCC 93026 www.vishay.com Vishay DSCC 93026 SuperTan Wet Tantalum Capacitors FEATURES Terminations: standard tin / lead (Sn / Pb) Very high capacitance 10 F to 1800 F 25 V to 125 V DC DC -55 C to +125 C Very low ESR High ripple current All tantalum case Hermetically sealed Low DCL Mounting: axial Vishays DSCC 93026 capacitor represents a major breakthrough in wet tantalum technology. Its unique APPLICATION NOTES cathode system provides the highest capacitance per unit a) No continuous reverse voltage permissible. volume. The design facilitates a doubling of capacitance, b) The peak of the applied AC ripple and the applied DC lower ESR and higher ripple current rating compared voltage must not exceed the DC voltage rating of the with conventional wet tantalum products. Moreover, the capacitor. DSCC 93026 has the capacitance stability of a solid c) Ripple current ratings by part number at 85 C and 40 kHz tantalum capacitor and there are no circuit impedance are included in the table. Ripple current correction factors restrictions. for other temperatures and frequencies are given on the The DSCC 93026 is housed in an all tantalum, hermetically next page. sealed case and is manufactured to withstand hazardous d) Transient reverse voltage surges are acceptable under environments. The DSCC 93026 is used widely in the the following conditions: defense and aerospace industries and whenever there is a the peak reverse voltage does not exceed 1.5 V and the space problem. peak current times the duration of the reverse transient does not exceed 0.05 As. In addition, the repetition frequency of the reverse voltage surge is less than 10 Hz. DIMENSIONS in inches millimeters Terminal welded 0.0253 0.002 0.64 0.05 dia. to case (no. 22 AWG) tinned nickel leads 0.250 (6.35) MAX. solderable and weldable 0.094 (2.38) MAX. Terminal location D dia. EL E within 0.031 of center 1 MAX. INSULATED CASE CODE D 0.016 0.41 L + 0.031 0.79 UNINSULATED E 0.250 6.35 MAX. 1 (DIA.) T1 0.188 4.78 0.219 5.56 0.453 11.51 1.500 38.10 T2 0.281 7.14 0.312 7.92 0.641 16.28 2.250 57.15 L2 0.281 7.14 0.312 7.92 1.008 25.60 2.250 57.15 T3 0.375 9.52 0.406 10.31 0.766 19.46 2.250 57.15 T4 0.375 9.52 0.406 10.31 1.062 26.97 2.250 57.15 Notes Material at egress is tantalum Approx. weight T1: 2.3 g, T2: 5.7 g Insulation sleeving will lap over the ends of the capacitor case T3: 9.4 g, T4: 14.8 g Revision: 06-Jul-15 Document Number: 40136 1 For technical questions, contact: tantalum vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DSCC 93026 www.vishay.com Vishay ORDERING INFORMATION 93026 -29 K S DSCC DRAWING NUMBER DASH NUMBER CAPACITANCE TOLERANCE K = 10 % S = sleeved M = 20 % U = unsleeved DEFENSE SUPPLY CENTER, COLUMBUS DRAWING NO. COLUMBUS, OHIO 93026 STANDARD RATINGS MAX. DCL MAX. MAX. CAPACITANCE CHANGE AC RIPPLE CAPACITANCE MAX. ESR (A) IMP. AT (%) 85 C AT 25 C CASE 120 Hz -55 C 40 kHz PART NUMBER 120 Hz CODE 85 C / () 120 Hz (mA) 25 C -55 C 85 C 125 C (F) 125 C () RMS 25 V AT 85 C 15 V AT 125 C DC DC 120 T1 1.3 1 5 25 -42 +8 +12 1250 93026-29(1)(2) 560 T2 0.83 2 10 12 -65 +10 +15 2100 93026-30(1)(2) 1100 L2 0.5 3 25 7 -60 +20 +45 3200 93026-57(1)(2) 1200 T3 0.65 5 20 7 -70 +12 +18 2600 93026-31(1)(2) 1800 T4 0.5 6 25 7 -75 +12 +20 3100 93026-32(1)(2) 2200 T4 0.5 10 80 10 -90 +30 +50 3200 93026-64(1)(2) 30 V AT 85 C 20 V AT 125 C DC DC 100 T1 1.3 1 5 25 -38 +8 +12 1200 93026-33(1)(2) 470 T2 0.85 2 10 15 -65 +10 +18 1800 93026-34(1)(2) 950 L2 0.5 5 30 7 -55 +18 +35 3200 93026-58(1)(2) 1000 T3 0.7 7 25 7 -70 +10 +18 2500 93026-35(1)(2) 1500 T4 0.6 12 35 6 -72 +10 +20 3000 93026-36(1)(2) 50 V AT 85 C 30 V AT 125 C DC DC 68 T1 1.5 1 5 35 -25 +8 +15 1050 93026-37(1)(2) 220 T2 0.9 2 10 17.5 -50 +8 +15 1800 93026-38(1)(2) 450 L2 0.6 3 25 7.5 -45 +12 +30 2900 93026-59(1)(2) 470 T3 0.75 3 25 10 -50 +8 +15 2100 93026-39(1)(2) 680 T4 0.7 5 40 8 -58 +10 +20 2750 93026-40(1)(2) 60 V AT 85 C 40 V AT 125 C DC DC 47 T1 2.0 1 5 44 -25 +8 +12 1050 93026-41(1)(2) 150 T2 1.1 2 10 20 -40 +8 +15 1650 93026-42(1)(2) 370 L2 0.6 3 25 9 -33 +9 +20 2900 93026-60(1)(2) 390 T3 0.9 3 25 15 -60 +8 +15 2100 93026-43(1)(2) 560 T4 0.8 5 40 10 -58 +8 +15 2750 93026-44(1)(2) 1000 T4 1.0 12 90 20 -90 +30 +50 3200 93026-65(1)(2) 75 V AT 85 C 50 V AT 125 C DC DC 33 T1 2.5 1 5 66 -25 +5 +9 1050 93026-45(1)(2) 110 T2 1.3 2 10 24 -35 +6 +10 1650 93026-46(1)(2) 250 L2 0.8 5 30 12 -30 +6 +15 2500 93026-61(1)(2) 330 T3 1.0 3 30 12 -45 +6 +10 2100 93026-47(1)(2) 470 T4 0.9 5 50 12 -55 +6 +10 2750 93026-48(1)(2) Note Part number definitions: (1) Capacitance tolerance. K = 10 %, M = 20 % (2) Case or body insulation. S = sleeved, U = unsleeved Revision: 06-Jul-15 Document Number: 40136 2 For technical questions, contact: tantalum vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000