HS22 Incremental Optical Encoder BEI Sensors Mechanical Specifications Shaft Bore: 0.500 (standard) 0.375, 0.250, 10mm, 8mm and 6mm available The HS22 series Allowable Misalignment: 0.010 T.I.R. on mating shaft of hollow shaft Bore Runout: 0.001 T.I.R. Starting Torque at 25C: 5-in-oz (max) incremental encoder Bearings: 52100 SAE high carbon steel offers application Shaft Material: 303 stainless steel Bearing Housing: Die cast aluminum with protective finish advantages over Cover: Drawn aluminum with protective finish 9 conventional optical Bearing Life: 7.5 X 10 revs (50, 000 hrs at 2500 RPM) Maximum RPM: 5,000 RPM encoders. This -4 2 Moment of Inertia: 10 X 10 oz-in-sec heavy duty unit Weight: 10 oz (max) is designed Electrical Specifications for ease of Code: Incremental Output Format, 2 channels in quadrature, one cycle (nominal) ungated index (other index options and commutation channels installation to a servo availableconsult factory). Cycles Per Shaft Turn: 100 to 2540 motor, the encoders flexible coupling Supply Voltage: 5, 1215, 2428 VDC fits over the driven motor shaft to provide an accurate, backlash-free Current Requirements: 120 mA typical, 175 mA max Voltage/Output: (see note 5) method of attachment. 28V/V: Line Driver, 528 VDC in, V = V out in 28V/5: Line Driver, 528 VDC in, V = 5 VDC out The mounting method eliminates the need for couplings, sprockets, 28V/OC: Open Collector, 528 VDC in, OC out Protection Level: Output short circuit or gearing. The integral flex mount provides for a 20-degree angular Frequency Response: adjustment. Through-shaft or blind shaft configurations of the HS22 100kHz allowable operating speed (RPM) = (100kHz/Resolution) x 60 Output Termination Pinouts: See table 1, back page encoder are available. Environmental Specifications Through-shaft units allow for applications where the center of the Enclosure Rating: NEMA 5 (IP50) for through shaft versions (TS) and NEMA 12 (IP52) for blind shaft (BS) versions encoder must be used for transmission of fluids, cabling, or optics. Temperature: Operating, 0 to 70 C extended temperature testing Blind shaft units are designed to mate with shaft lengths of 0.50 to available, -40 to 85 storage, -20 to 90 C. Shock: 50 gs for 11 msec duration 1.50 inch. Standard outputs for both configurations incude: A and B in Vibration: 5 to 2000 Hz 10 gs quadrature with index and optional commutation signals for brushless Humidity: 98% RH non-condensing motor control. NOTES AND TABLES: All notes and tables referred to in the text can be found on the back page. HS22 Incremental Ordering Options for assistance call 800-350-2727 Use this diagram, working from left to right to construct your model number (example: HS22F-50-R1-TS-256-ABZC-28V/V-SC18). HS22 F R1 HOUSING: TETHER: SPECIAL CHANNELS: OUTPUT F = Standard R1 = Flexmount FEATURES: RESOLUTION TERMINATION A, AB, ABZ SHAFT BORE: Blank = None NUMBER OF CYCLES: SHIELDED CABLE: ABZC 1/2 (Std.) = 50 TYPE: S = Special 100, 200, 250, SC18 = 18.0 10mm = 39 Hollow Shaft COMMUTATION 256, 360, 480, 500, CONNECTOR 3/8 = 37 VOLTAGE/OUTPUT: SHAFT/SEAL: 2.2 Diameter TRACKS: 1000, 1024, 1440, OPTIONAL: 8mm = 31 28V/V = 528V in/out TS = Through Shaft Blank = None 1800, 2000, 2048, Blank = None 1/4 = 25 28V/5 = 528V 5V in/ out BS = Blind Shaft C2 = 2 pole pairs 2500, 2540 Consult Factory 6mm = 24 28V/OC = 528V OC in/ out tel: 805-968-0782 /800-350-2727 fax: 805-968-3 154 / 800-960-2726 7230 Hollister ave., Goleta, ca 93117-2807 www.beiied.com specification no. 924-02068 rev.06-10 These commodities, technology or software if exported from the United States must be in accordance with the Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.HS22 Incremental Optical Encoder BEI Sensors Dimensions Notes 1. Mounting is usually done either using the D-style square flange mount, E- or G-style servo mounts, or one of the standard HS22 Diagram Thru Shaft Blind Shaft face mounts, F1 for example. Consult factory for additional face (1.74) (1.74) mount options. 20 1.35 20 1.35 (1.64) (.35) (1.64) (.35) 2.The shaft seal is recommended in virtually all installations. The MAX MAX .157 WIDE .157 WIDE .10 .10 most common exceptions are applications requiring a very low starting 20, 3X 20, 3X R. 1.450 R. 1.450 MAX MAX EQL SP ON A EQL SP ON A torque or those requiring operation at both high temperature and 2.61 B.C. 2.61 B.C. 8 SHAFT high speed. 8 SHAFT LOCKING SCREW LOCKING SCREW 90 APART, 2X 90 APART, 2X 3. Non-standard index widths and multiple indices are available by special order. Consult factory. 4. Complementary outputs are recommended for use with line driver 1.00 1.00 type (source/sink) outputs. When used with differential receivers, this combination provides a high degree of noise immunity. 5. Output ICs: Output ICs are available as either Line Driver (LD) or .75 .75 NPN Open Collector (OC) types. Open Collectors require pull-up resis- TYP TYP tors, resulting in higher output source impedance (sink impedance BORE BORE is similar to that of line drivers). In general, use of a Line Driver style +0.003/-0.000 +0.003/-0.000 2.22 2.22 BLIND SHAFT output is recommended. Line Drivers source or sink current and their BLIND SHAFT TO MATE WITH TO MATE WITH lower impedance mean better noise immunity and faster switching SHAFT LENGTHS OF SHAFT LENGTHS OF +1.00 +1.00 .5 TO 1.5 times. Warning: Do not connect any line driver outputs directly to .5 TO 1.5 -0.00 -0.00 15 15 18.0 circuit common/OV, which may damage the driver. Unused outputs 18.0 should be isolated and left floating. Our applications specialists would be pleased to discuss your system requirements and the compatibility of your receiving electronics with Line Driver type outputs. 28V/V: Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28 VDC +/- 5% standard (Note: V = V ). This driver out in is TTL compatible when used with 5 volt supply. Supply lines are HS22 THRU SHAFT HS22 BLIND SHAFT HS22 THRU SHAFT HS22 BLIND SHAFT protected against overvoltage to 60 volts and reverse voltage. Outputs Table 1 are short circuit protected for one minute. Supply current is 120 mA typical (plus load current). This is the recommended replacement for 3904R and 7406R open collector outputs with internal pullup resistors. Output Termination Pinouts It is also a direct replacement for any 4469, 88C30, 8830 or 26LS31 line driver STANDARD INCREMENTAL OUTPUTS OPTION COMMUTATION OUTPUTS 28V/5: Multi-voltage Line Driver (7272*): 100 mA source/sink. Input COLOR FUNCTION COLOR FUNCTION voltage 5 to 28 VDC +/- 5% standard, internally regulated with 5V (TTL compatible) logic out. Supply lines are protected against overvolt- YEL A GRY U age to 60 volts and reverse voltage. Outputs are short circuit protected WHT/YEL A WHT/YGRY U for one minute. Supply current is 90 mA typical (plus load current). BLU B BRN V 15V/V: Multi-voltage Line Driver (4469*): 100 mA source/sink. Input voltage 5 to 15 VDC +/- 5% standard (Note: V = V ). TTL compat- out in WHT/BLU B WHT/BRN V ible when used with 5 volt supply. Supply lines are protected against ORN Z VIO W overvoltage to 60 volts and reverse voltage. Outputs are short circuit protected for one minute. Supply current is 90 mA typical (plus load WHT/ORN Z WHT/VIO W current). This is a direct replacement for the 4469 Line Driver. RED +V (SUPPLY) 28V/OC: NPN Open Collector (3904*, 7273*). Current sink of 80 mA BLK O V (GROUND) max. Current sourced by external pull- up resistor. Output can be DATA TRACKS pulled up to voltage other than supply voltage (30 V max). Input volt- GRN CASE GROUND + age 5 to 28 VDC /- 5% standard. Supply current is 120 mA typical. 1~ This replaces prior ICs with designations of 3904, 7406, 3302, 681 1/2~ and 689. DATAA Figure 1 Output Waveform 5V/OCR, 15V/OCR, 24V/OCR: Open Collector (3904R*, 7406R*, 1/4~ (NOM.) 7273R*): Current sink of 70 mA max. Includes internal pull-ups DATAB sized at approximately 100 ohms/volt. Max current source is 10 mA. 1 CYCLE 1/4~ (MIN.) Supply current is 100 mA typical, 120 mA with internal pull-ups. The INDEX UNGATED 90 Deg. 5V/OCR, 15V/OCR and 24V/OCR are often replaced by the 28V/V in INDEX TRANSITIONS TO OCCUR IN system upgrades. HI SHADED AREAS 3904, 3904R, 4469, 5V/V, 5V/OC, 5V/OCR, 9V/OC: Intrinsically safe LO A CCW ROTATION VIEWING FACE line driver and open collector outputs. These drivers are specific to intrinsically safe encoders, and are installed per the appropriate control drawings listed in Table 2.1 on page 48 of the 2008 BEI Spec Guide. B COMMUTATION TRACKS (3 PHASE, N = NUMBER OF POLE PAIRS) 6. Special S at the end of the model number is used to define a (USE N = 2 FOR A 4-POLE MOTOR) variety of non-standard features such as special shaft lengths, voltage options, or special testing. Please consult the factory to discuss your Z INDEX (REF) special requirements. 360 / N. MECHANICAL 7. Higher frequency response may be available. Please consult with A 180 ELECT the factory. 8. Extended temperature ratings are available in the following ranges: COMM U B -40 to 70C, -40 to 85C, 20 to 105C and 40 to 105C depend- 120 ELECT ing on the particular model. Some models can operate down to -55C. COMM V Extended temperature ranges can affect other performance factors. Z 240 ELECT Consult with factory for more specific information. COMM V 9. Mating straight plug receptacles may be ordered from the factory: For M12 use MS3116F12-10S, For M14 use MS3106F14S-6S CCW Rotation Viewing Face For M14/19 use MS3116J14-19S, For M16 use MS3106F16S-1S For M18 use MS3106F18-1S, For M20 use MS3106F20-29S tel: 805-968-0782 /800-350-2727 fax: 805-968-3 154 / 800-960-2726 7230 Hollister ave., Goleta, ca 93117-2807 www.beiied.com These commodities, technology or software if exported from the United States must be in accordance with the Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.