SX1230SKA433

SX1230 ADVANCED COMMUNICATIONS & SENSING DATASHEET SX1230 - Integrated Transmitter IC Narrow/wideband 315 MHz, 434 MHz 868 MHz and 915 MHz band Transmitter GENERAL DESCRIPTION APPLICATIONS The SX1230 is a fully integrated transmitter which can Remote Keyless Entry (RKE) operate in the 315, 434, 868 and 915 MHz licence free ISM bands. Remote Control / Security Systems The transmitter has two modes of operation, a conventional Voice and Data RF Communication Links MCU controlled mode and a stand-alone mode which Process and building / home control enables the SX1230 to download configuration and 2 Active RFID messages from an E PROM in response to a user input. Stand-alone mode makes the SX1230 ideal for miniaturized AMR / AMI Platforms or low cost remote keyless entry (RKE) applications. It also offers the unique advantage of narrow-band and wide-band KEY PRODUCT FEATURES communication in a range of modulation formats. +17 dBm to -18 dBm Programmable output power. The SX1230 offers high RF output power and channelized operation suited for the European (ETSI EN 300-220-1), Bit rates up to 600 kbits / sec. North American (FCC part 15.231, 15.247 and 15.249) and FSK, GFSK, MSK, GMSK and OOK modulation. Japanese (ARIB T-67) regulatory standards. Stand-alone mode: No need for a host MCU. ORDERING INFORMATION Consistent RF performance over a 1.8 to 3.7 V range. Low phase noise (-95 dBc/Hz at 50 kHz) with automated Part Number Temperature Range Qty. per Reel Package PLL calibration and fully integrated VCO and loop filter. SX1230I066TRT -40 C to +85 C 3000 MLPQ-24 (4x4mm) On chip RC timer for timer / wake-up applications. Low battery detection. Pb-free, Halogen free, RoHS/WEEE compliant product MLPQ-24 4x4mm Package - Operating Range -40 +85C 1 SX1230, Revision 4 December 2015 Page 1 www.semtech.com 2015 Semtech Corp. 1. ST0002 01 USSX1230 ADVANCED COMMUNICATIONS & SENSING DATASHEET Table of contents Section Page 1. General Description..................................................................................................................................................4 1.1. Simplified Block Diagram ..................................................................................................................................4 1.2. Pin Diagram ......................................................................................................................................................5 1.3. Pin Description...............................................................................................................................................6 2. Electrical Characteristics ..........................................................................................................................................7 2.1. ESD Notice .......................................................................................................................................................7 2.2. Absolute Maximum Ratings ..............................................................................................................................7 2.3. Operating Range...............................................................................................................................................7 2.4. Electrical Specifications....................................................................................................................................8 3. Timing Characteristics ..............................................................................................................................................9 4. Working Modes of the SX1230...............................................................................................................................10 4.1. Operating Modes ............................................................................................................................................10 4.2. Application Modes...........................................................................................................................................10 4.2.1. Stand Alone Mode .................................................................................................................................. 10 4.2.2. MCU Mode...............................................................................................................................................11 5. Operation of the SX1230 ........................................................................................................................................12 5.1. Main Parameters............................................................................................................................................ 12 5.1.1. Center Frequency ................................................................................................................................... 12 5.1.2. Frequency Deviation ............................................................................................................................... 12 5.1.3. Bit Rate ................................................................................................................................................... 12 5.2. Synthesizer.................................................................................................................................................... 13 5.3. The Power Amplifier....................................................................................................................................... 14 6. Digital Control and Interface .................................................................................................................................. 15 6.1. Stand Alone Mode ......................................................................................................................................... 15 6.1.1. State Machine Description ...................................................................................................................... 15 6.1.2. Memory Organization of the E2PROM ................................................................................................... 15 6.1.3. Periodic mode ......................................................................................................................................... 17 6.1.4. Low Battery Indicator: Stand Alone Mode............................................................................................... 18 6.1.5. Low Battery Indicator: MCU Mode .......................................................................................................... 18 6.2. MCU Mode..................................................................................................................................................... 18 6.2.1. SPI Operation ......................................................................................................................................... 18 6.2.2. Data and Data Clock Usage....................................................................................................................20 6.3. SX1230 Register Description........................................................................................................................ 21 7. SX1230 Application Circuits ...................................................................................................................................27 7.1. SX1230 E2PROM Mode Application Circuit ...................................................................................................27 7.2. SX1230 MCU Mode Application Circuit ..........................................................................................................28 7.3. Complete RKE Application Circuit ..................................................................................................................28 SX1230, Revision 4 December 2015 Page 2 www.semtech.com 2015 Semtech Corp. ST0002 01 US