10SVP270M

4. SPECIFICATIONS FOR EACH SERIES Conductive polymer type SVPSeries Standard SMD type Standard SMD type product Use for surface mounted type switching power supplies. This product can support lead free-reflow. ( 2). Marking : Polarity( ), Rated voltage, Lot.No. (Purple) SVP(Upper E7), Rated capacitance. Specifications Items Conditions Characteristics Category temperature range -55C to +105C Tolerance on rated capacitance 120Hz M: 20% Tangent of loss angle Less than or equal to the value of Table7 120Hz After 2 minutes Leakage current 1 Less than or equal to the value of Table7 ESR Less than or equal to the value of Table7 Characteristics of impedance Based the value at Z / Z 20C 0.75 to 1.25 -55C ratio at high temp. and low temp. 100KHz +20C +105C Z / Z 20C 0.75 to 1.25 C/C Within 20% 105C, 2,000h, Rated tan 1.5 times or less than an initial standard Endurance voltage applied ESR 1.5 times or less than an initial standard (25V20V applied) Leakage current Below an initial standard C/C Within 20% 60C, 90 to 95%RH, tan 1.5 times or less than an initial standard Damp heat (Steady state) 1,000h, ESR 1.5 times or less than an initial standard No-applied voltage Leakage current Below an initial standard (after voltage processing) C/C Within 10% Resistance to tan 1.3 times or less than an initial standard 2 (VPS) (230C X 75s) soldering heat ESR 1.3 times or less than an initial standard Leakage current Below an initial standard (after voltage processing) 1 In case of some problems for measured values, measure after applying rated voltage for 2.5 to 20V products or 20V for 25V products for 120 minutes at 105C . (unit : mm) 2 Refer to Page 56 for reflow soldering conditions. +0.1 Size Code L W0.2 H0.2 C0.2 R P0.2 D0.5 Dimensions -0.4 0.2max. A5 4.0 5.4 4.3 4.3 5.0 0.6 to 0.8 1.0 W B6 5.0 5.9 5.3 5.3 6.0 0.6 to 0.8 1.4 C6 6.3 5.9 6.6 6.6 7.3 0.6 to 0.8 2.1 E7 8.0 6.9 8.3 8.3 9.0 0.6 to 0.8 3.2 F8 10.0 7.9 10.3 10.3 11.0 0.6 to 0.8 4.6 E12 8.0 11.9 8.3 8.3 9.0 0.8 to 1.1 3.2 L R F12 10.0 12.6 10.3 10.3 11.0 0.8 to 1.1 4.6 Size List RV : Rated voltage (SV) : Surge (room temperature) RV 2.5 4 6.3 10 16 20 25 Recommended land pattern SV F 3.3 5.2 8.2 11.5 18.4 23.0 25.0 dimension of PWB 3.3 A5 4.7 A5 6.8 A5 C6 10 A5 B6 E7 15 A5 B6 22 A5 B6 C6 F8 27 C6 33 A5 B6 E7 E12 a 39 B6 C6 47 B6 C6 E7 b 56 C6 E7 F8 F12 68 B6 F8 82 C6 E7 100 C6 F8 E12 Size Code ab c 120 C6 E7 150 C6,E7 E7,F8 F8 F12 A5 1.0 6.2 1.6 180 F8,E12 220 E7,F8 1.4 7.4 1.6 C6 B6 270 F8 C6 2.1 9.1 1.6 330 E7 F8 F8,E12 F12 470 F8,E12 2.8 11.1 1.9 E7 560 E12 F12 680 E12 F8 4.3 13.1 1.9 F8 820 F12 1200 F12 E12 2.8 11.1 1.9 1500 F12 4.3 13.1 1.9 F12 For the minimum packing quantity, please refer to page 55. 30 D H P C c4. SPECIFICATIONS FOR EACH SERIES Table7 SVP Series Characteristics List Rated Rated ESR Rated Tangent of Leakage Size Part Number Voltage Capacitance 100kHz to 300kHz ripple current loss angle current ( A) Code 1 (V) ( F) (m ) (max.) (mArms) (max.) (max.) 2 16SVP3R3M 16 3.3 260 660 0.07 26.4 10SVP4R7M 10 4.7 240 670 0.08 23.5 10SVP6R8M 10 6.8 240 670 0.09 34.0 10SVP10M 10 10 220 700 0.10 50.0 A5 10SVP15M 10 15 200 740 0.10 75.0 6SVP22M 6.3 22 200 740 0.12 69.3 4SVP33M 4 33 200 740 0.15 66.0 20SVP10M 20 10 120 1020 0.10 100 16SVP15M 16 15 120 1020 0.10 120 16SVP22M 16 22 90 1060 0.10 176 10SVP33M 10 33 70 1100 0.12 165 B6 6SVP47M 6.3 47 70 1100 0.12 148 4SVP39M 4 39 70 1100 0.12 78 4SVP68M 4 68 60 1400 0.12 136 25SVP6R8M 3 25 6.8 80 1200 0.10 85 20SVP22M 20 22 60 1450 0.10 88 20SVP27M 20 27 60 1450 0.10 108 16SVP39M 16 39 50 1620 0.10 125 10SVP47M 10 47 50 1620 0.12 94 C6 10SVP56M 10 56 45 1700 0.12 112 6SVP82M 6.3 82 45 1700 0.12 103 6SVP100M 6.3 100 40 1810 0.12 126 6SVP120MV 6.3 120 17 2780 0.12 151 4SVP150MX 4 150 40 1810 0.12 120 2R5SVP220M 2.5 220 23 2390 0.12 110 25SVP10M 3 25 10 60 1500 0.10 125 20SVP33M 20 33 45 1890 0.12 132 20SVP47M 20 47 45 1890 0.12 188 16SVP56M 16 56 45 1890 0.12 179 16SVP82M 16 40 2120 0.12 262 82 10SVP120M 10 120 35 2560 0.12 240 E7 10SVP150MX 10 150 35 2560 0.12 300 6SVP220MX 6.3 220 35 2560 0.12 277 4SVP150M 4 150 35 2560 0.12 120 4SVP330M 4 330 35 2560 0.12 264 25SVP22M 3 25 22 50 2000 0.10 275 20SVP56M 20 56 40 2400 0.12 224 20SVP68M 20 68 40 2400 0.12 272 16SVP100M 16 100 35 2670 0.12 320 16SVP150M 16 150 30 3020 0.12 480 16SVP180MX 16 180 30 3020 0.12 576 10SVP150M 10 150 30 3020 0.12 300 F8 0.12 540 10SVP270M 10 270 25 3700 10SVP330MX 10 330 25 3700 0.12 660 6SVP220M 6.3 220 25 3700 0.12 277 6SVP330M 6.3 330 25 3700 0.12 416 6SVP470MX 6.3 470 25 3700 0.12 592 4SVP680M 4 680 25 3700 0.12 544 3 25SVP33M 25 33 30 2980 0.12 413 20SVP100M 20 100 24 3320 0.15 400 16SVP180M 16 180 20 3640 0.15 576 E12 10SVP330M 10 330 17 3950 0.15 660 6SVP470M 6.3 470 15 4210 0.15 592 4SVP560M 4 560 13 4520 0.15 448 2R5SVP680M 2.5 680 13 4520 0.15 340 25SVP56M 3 25 56 28 3800 0.12 700 20SVP150M 20 150 20 4320 0.15 600 16SVP330M 16 330 16 4720 0.15 792 10SVP560M 10 560 13 5230 0.15 840 F12 6SVP820M 6.3 820 12 5440 0.15 775 4SVP1200M 4 1200 12 5440 0.18 960 2R5SVP1500M 2.5 1500 12 5440 0.18 750 Capacitance tolerance : M 20% 2 After 2 minutes 3 The surge voltage of 25V products is 25V. Please consider SVPD series 25V products (whose surge voltage is 29V) in placing a new order. Frequency coefficient for ripple current Frequency 120Hz f 1kHz 1kHz f 10kHz 10kHz f 100kHz 100kHz f 500kHz Coefficient 0.05 0.3 0.7 1 31