885128 2.4 GHz WLAN/BT LTE Co-Existence Filter General Description The 885128 is a high-performance, high power Bulk Acoustic Wave (BAW) band-pass filter with extremely steep skirts, simultaneously exhibiting low loss in the WiFi band and high near-in rejection in the approximate LTE bands. 885128 is specifically designed to enable coexistence of WiFi and LTE signals within the same device or in close proximity to one another. The 885128 uses common module packaging techniques 1.1 X 0.9 X 0.50 mm to achieve the industry leading size 1.1 x 0.9 x 0.50 mm footprint. The filter exhibits excellent power handling Product Features capabilities. Low Loss in WLAN band with extended upper corner for inclusion of Bluetooth High Rejection in B30/B38/B7/B41 bands Industry leading small size: 1.1 x 0.9 x 0.5 mm Functional Block Diagram Performance over 40 to +95 C Single Ended operation Gnd RoHS compliant, Pb-free module package Output 5 4 Input 1 Applications 2 3 Gnd WiFi bandpass filter that enables the coexistence of (LTE/TD-LTE) & Wi-Fi Gnd Portable Hotspots Top View Wi-Fi Routers and LTE Gateways Pin Configuration - Single Ended Smart Meters Wi-Fi Access Points Pin No. Label Small Cells 1 Input 4 Output 2,3,5 Function label Note: 1. Pin 1 must be used for input. The large signal performance of this filter (power handling and nonlinear response) is not symmetric Ordering Information Part No. Description 885128 Packaged Part 885128-EVB Evaluation board Standard T/R size = 15,000 units/reel Advanced Data Sheet: REV F October 2018 - 1 of 8 - www.qorvo.com Subject to change without notice 885128 2.4 GHz WLAN/BT LTE Co-Existence Filter (1) Absolute Maximum Ratings Notes: Parameter Rating 1. Operation of this device outside the parameter ranges given may Storage Temperature -40C to 125C cause permanent damage. Operating Temperature -40C to +105C 2. Max CW signal applied for up to 500ms with no damage. (2) RF Input Power +36 dBm Pin 1 must be used for input. The large signal performance of this filter (power handling and nonlinear response) is not symmetric. (1) Electrical Specifications (2) Test conditions unless otherwise noted: 30C to +85C (3) (5) Parameter Conditions Min Typ Max Units 2402.5 2421.5 MHz (WiFi Ch.1) 1.5 1.7 - 2407.5 2426.5 MHz (WiFi Ch.2) 1.3 1.5 - 2412.5 2471.5 MHz (WiFi Ch.3-11) 1.1 1.4 (6) Insertion Loss - dB 2412.5 2471.5 MHz (WiFi Ch.3-11)(19 MHz sliding window) 1.3 1.5 - 2457.5 2476.5 MHz (WiFi Ch.12) 1.3 1.6 - 2462.5 2481.5 MHz (WiFi Ch.13) 1.5 1.9 2402.5 2421.5 MHz (WiFi Ch.1) - 0.9 1.4 2407.5 2426.5 MHz (WiFi Ch.2) - 0.7 0.9 Amplitude Variation 2412.5 2471.5 MHz (WiFi Ch.3-11) - 0.7 1.1 dB p-p 2457.5 2476.5 MHz (WiFi Ch.12) - 0.5 1.2 2462.5 2481.5 MHz (WiFi Ch.13) - 0.9 2.0 - 925 960 MHz 32 33 1559 1606 MHz 32 33 - - 2110 2170 MHz 42 47 (7) 2300 2370 MHz 33 39 - (7) - 2500 2505 MHz (+25 to +85C) 31 38 (7) 2500 2505 MHz (30 to +25C) 23 38 - Rejection dB (7) - 2505 2570 MHz (+25 to +85C) 44 50 (7) 2505 2570 MHz (30 to +25C) 41 50 - (7) - 2570 2620 MHz 47 50 (7) 2620 2690 MHz 45 49 - - 4800 5000 MHz 27 33 7200 7500 MHz 27 31 - Input /Output VSWR 2402.5 2481.5 MHz - 1.6 2.0 - (8) RF Input Power 2400 2483 MHz - 24 - dBm (9) Source Impedance (single-ended) - 50 - (9) Load Impedance (single-ended) - 50 - Notes: 1. All specifications are based on the Qorvo schematic shown on page 5. 2. In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature. 3. Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances. 4. An external impedance matching network with 2% tolerance will be necessary to achieve the stated specifications. 5. Typical values are based on average measurements at room temperature. 6. Data is the integrated value of the linear s-parameter over a 19 MHz range in the indicated band at the specified temperature. 7. Data is the integrated value of the linear s-parameter over 5MHz range at the specified temperature. 8. Input power applied for a minimum of 5,000 hrs. at 55C in the frequency band specified. 9. This is the optimum impedance in order to achieve the performance shown. Advanced Data Sheet: REV F October 2018 - 2 of 8 - www.qorvo.com Subject to change without notice