PG1096.472NLT

SMT Power Inductors Round wire Coils PG1096NL series Inductance Range: 1.5uH to 82uH Height: 14.8mm Max Current Rating: up to 65Apk No Thermal Aging Footprint: 26mm x 26mm Max RoHS Compliant 1 Electrical Specifications 25 C - Operating Temperature -40C to 130C 5 Saturation Controlled Electrical Specs. Current Isat 6 Inductance (A TYP) Heating Current 3 7 Irated Core Loss Factor 2 Part Number Irated Idc (K2) (A) 4 (A TYP) DCR Inductance H TYPICAL (m) 0Adc 25C 100C MAX (H 20%) PG1096.152NL 1.35 50 0.85 1.5 65 50.5 50 27.9 PG1096.252NL 2.25 45 1.2 2.5 55 43 45 31 PG1096.472NL 4.2 35 1.8 4.7 40 31 35 43.7 PG1096.682NL 6 30 2 6.8 35 27.5 30 50.6 PG1096.103NL 9 24.5 3.15 10 28 21.8 24.5 62 PG1096.183NL 16 18.5 5 18 21 16.5 18.5 83.6 PG1096.223NL 19.5 17 5.5 22 19 14.8 17 90.9 PG1096.333NL 29.5 13.5 10.5 33 15.5 12 13.5 111.5 PG1096.473NL 42.3 11 12.5 47 13 10 11 134.4 PG1096.683NL 61 9.5 15 68 11 8.6 9.5 168.5 PG1096.823NL 73.5 8.5 22 82 10 7.8 8.5 179.3 Notes: 1. Actual temperature of the component during system operation (ambient plus 7. Core loss approximation is based on published core data: 1.42 2.57 temperature rise) must be within the standard operating range. Core Loss = K1 * (f) * (K2I*0.1) in mW 2. Inductance at Irated is a typical inductance value for the component taken at rated K1=2.86E-06 (2.50E-06 FOR PG1096.152NL) current. f = switching frequency in KHz 3. The rated current as listed is either the saturation current ( 25C) or the heating K1 & K2 = core loss factors current depending on which value is lower. I= delta I across the component in Ampere 4. The DCR of the part is measured at an ambient temperature of 20C3C from point a K2I=one half of the peak to peak flux density across the component in Gauss to b as shown below on the mechanical drawing. 8. Unless otherwise specified, all testing is made at 100kHz, 0.1Vac 5. The saturation current, Isat, is the current at which the component inductance drop 9. Optional Tape & Reel packaging can be ordered by adding a T suffix to the part by 20% (typical) at an ambient temperature. This current is determined by placing number (i.e. PG1096.223NL becomes PG1096.223NLT). Pulse complies with industry the component in the specified ambient environment and applying a short duration standard tape and reel specification EIA481. The tape and reel for this product has a pulse current (to eliminate self-heating effect) to the component. width (W=44.0mm), pitch (Po=36.0mm) and depth (Ko=15.6mm). 6. The heating current, Idc, is the DC current required to raise the component tempera- 10. The core is a conductive material so care should be taken when mounting this com- ture by approximately 40C. The heating current is determined by mounting the ponent over an exposed via or if the voltage across the terminals exceeds 24V. Trickle component on a typical PCB and applying current for 30 minutes. The temperature is current through the core material may generate additional losses and potential measured by placing the thermocouple on top of the unit under test. Take note that overheating. Please contact Pulse to discuss an alternative solution if required. the components performance varies depending on the system condition. It is sug- gested that the component be tested at the system level, to verify the temperature rise of the component during system operation. SMT Power Inductors Round wire Coils PG1096NL series Mechanicals Schematic PG1096.XXXNL 1 2 3 *PIN 3 IS FOR MECHANICAL SUPPORT ONLY AND HAS NO INTERNAL ELECTRICAL CONNECTION Lead Width H P Part Number (X) Ref (Height) (Pin Pitch) PG1096.152NL 3.0mm 13mm PG1096.252NL 3.0mm PG1096.472NL 3.0mm PG1096.682NL 3.0mm PG1096.103NL 3.0mm 17.001.00mm PG1096.183NL 3.0mm 14.8mm PG1096.223NL 3.0mm PG1096.333NL 3.0mm PG1096.473NL 3.0mm PG1096.683NL 3.0mm PG1096.823NL 2.3mm 17.001.70mm Weight.......................... 34 .0 grams (28.0 grams for PG1096.152NL) Tape and Reel....................60/reel Inches Dimensions: mm 0.01 Unless otherwise specified, all tolerences are 0.25