Z-15GW2 OMI

General-purpose Basic Switch Z CSM Z DS E 3 1 Best-selling Basic Switch Boasting High Precision and Wide Variety A large switching capacity of 15 A with high repeat accuracy. A wide range of variations in contact form for your selection: basic, split-contact, maintained-contact, and adjustable contact gap types. A series of standard models for micro loads is available. A series of molded terminal-type models incorporating safety terminal protective cover is available. Be sure to read Safety Precautions on page 22 and Safety Precautions for All Basic Switches. Model Number Structure Configuration Refer to page 3. Basic models General-purpose Refer to page 5. Drip-proof Without terminal protective cover Refer to page 5. With terminal protective cover Refer to page 2. Molded terminal Refer to page 4. Split-contact models General-purpose Refer to page 4. Maintained-contact models General-purpose Basic Models Split-contact Models This type is identical in construction to the general-purpose basic General-purpose switch except that it has two pairs of simultaneous acting contacts A variety of actuators is available for a wide range of application. by splitting moving contacts. The contact mechanism of models for micro loads is a crossbar Since the moving contacts are connected to a common terminal, type with gold-alloy contacts, which ensures highly reliable either parallel or series connection is possible. operations for micro loads. Highly reliable micro load switching is ensured if the model is used Contact Gap: as a twin-contact switch. H2: 0.20 mm (extra-high-sensitivity) H: 0.25 mm (high-sensitivity, micro voltage current load) Maintained-contact Models G: 0.5 mm (standard) E: 1.8 mm (high-capacity) The maintained-contact type has a reset button at the bottom of the F: 1.0 mm (split-contact models) switch case, in addition to the pushbutton (plunger) located on the opposite side of the reset button. Use these buttons alternately. Drip-proof Since the Switch has greater pretravel than overtravel, it is suitable for use in reversible control circuits, manual reset circuits, safety These Switches use a rubber boot on the actuator and adhesive fill limit circuits, and other circuits which are not preferable for between the case and cover to increase resistance to drips. automatic resetting. (For further details, refer to individual Models with drip-proof terminal protective covers and molded datasheets.) terminals with resin filling are also available. 1Z Model Number Legend Basic Models Standard Models (Drip-proof Type/Molded Terminals) Z- - Z- 55-M M (1)(2)(3)(4) (5) (1) (2)(3) (4) (1) Ratings (1) Drip-proof Type 01 : 0.1 A (micro load) (2) Lead Outlets 15 : 15 A None : VSF (2) Contact Gap 19 : VCT H2 : 0.20 (extra-high-sensitivity) (3) Directions of Lead H : 0.25 mm (high-sensitivity, L Type D Type R Type Outlets (See following micro load) diagrams.) G : 0.5 mm (standard) E : 1.8 mm (high-capacity) L:Left (3) Actuator R : Right D : Descending None : Pin plunger (4) Length of Lead S : Slim spring plunger D : Short spring plunger Outlets K : Spring plunger (medium OP) 1: 1 m K3 : Spring plunger (high OP) 3: 3 m Q3 : Panel mount plunger (medium OP) Split-contact Models Maintained-contact Models Q : Panel mount plunger (medium OP) Z-10F Y-B Z-15-E R Q8 : Panel mount plunger (high OP) (1) (2)(3)(4) (5) (1) (2)(3)(4) Q22 : Panel mount roller plunger (1) Ratings (1) Ratings Q21 : Panel mount cross roller plunger 10 : 10 A (split-contact models) 15 : 15 A L : Leaf spring (high OF) (2) Contact Gap (2) Contact Gap L2 : Roller leaf spring F : 1 mm (high-capacity) E : 1.8 mm (high capacity) W21 : Short hinge lever (3) Actuator (3) Actuator W : Hinge lever (low OF) None : Pin plunger None : Pin plunger W3 : Hinge lever (medium OF) S : Slim spring plunger S : Slim spring plunger W32 : Hinge lever (high OF) D : Short spring plunger W : Hinge lever W4 : Low-force hinge lever Q : Panel mount plunger (4) Structure W44 : Long hinge lever Q22 : Panel mount roller plunger R : Maintained-contact models W78 : Low-force wire hinge lever W : Hinge lever (low OF) W22 : Short hinge roller lever W52 : Low-force wire hinge lever W2 : Hinge roller lever (high OF) M22 : Reverse short hinge roller W22 : Short hinge roller lever lever W2 : Hinge roller lever (4) Construction W25 : Hinge roller lever (large roller) Y : Split-contact models W49 : Short hinge cross roller lever (5) Terminals W54 : Hinge cross roller lever W2277 : Unidirectional short hinge B : Screw terminal roller lever (low OF) (with toothed washer) M : Reverse hinge lever M22 : Reverse short hinge roller lever M2 : Reverse hinge roller lever NJ : Flexible rod (high OF) NJS : Flexible rod (low OF) (4) Degree of Protection None : General-purpose 55 : Drip-proof (not include the terminals) A55 : Drip-proof (including the terminals) (5) Terminals None : Solder terminal B : Screw terminal (with toothed washer) B5V : Screw terminal with terminal cover (for Z-15G A55 only) Note: For combinations of models, Ordering Information on page 3 to 6. 2