PCA9509AGM,125

PCA9509A 2 Low power level translating I C-bus/SMBus repeater Rev. 3 17 May 2018 Product data sheet 1. General description 2 The PCA9509A is a level translating I C-bus/SMBus repeater with two voltage supplies 2 that enables processor low voltage 2-wire serial bus to interface with standard I C-bus or 2 SMBus I/O. While retaining all the operating modes and features of the I C-bus system 2 during the level shifts, it also permits extension of the I C-bus by providing bidirectional 2 buffering for both the data (SDA) and the clock (SCL) lines, thus enabling the I C-bus or SMBus maximum capacitance of 400 pF on the higher voltage side. Port A allows a voltage range from 0.8 V to 2.0 V and requires no external pull-up resistors due to the internal current source. Port B allows a voltage range from 2.3 V to 5.5 V and is overvoltage tolerant. Both port A and port B SDA and SCL pins are high-impedance when the PCA9509A is unpowered. The bus port B drivers are compliant with SMBus I/O levels, while port A uses an offset LOW which prevents bus lock-up and allows the bidirectional nature of the device. Port A uses a current source for pull-up and an offset pull-down driver. This results in a LOW on the port A accommodating smaller voltage swings. The output pull-down on the port A internal buffer LOW is set for approximately 0.2V , while the input threshold of the CC(A) internal buffer is set about 50 mV lower than that of the output voltage LOW. When the port A I/O is driven LOW internally, the LOW is not recognized as a LOW by the input. This prevents a lock-up condition from occurring. The output pull-down on the port B 2 drives a hard LOW and the input level is set at 30 % of SMBus or I C-bus voltage level 2 which enables port B to connect to any other I C-bus devices or buffer. The PCA9509A drivers are not enabled unless V is above 0.7 V and V is above CC(A) CC(B) 1.7 V. The enable (EN) pin can also be used to turn on and turn off the drivers under system control. Caution should be observed to change only the state of the EN pin when the bus is idle. The PCA9509A is similar to the PCA9509 but offers lower A port voltage range to 0.8 V to accommodate lower voltage processors and disables the current mirrors when disabled to reduce standby power.PCA9509A NXP Semiconductors 2 Low power level translating I C-bus/SMBus repeater 1.1 Selection recommendations The PCA9509A is recommended for all applications except in the following cases: PCA9509P should be used if an external A-port pull-up resistor is required to adjust current for noise margin considerations or to reduce operating current consumption even more. The PCA9509 should be used if instant on from disable is required with A Port voltage greater than 1.0 V and larger standby current is not a concern. Table 1. Device selection recommendation Concern Recommended device PCA9509 PCA9509A PCA9509P A-port lowest voltage 0.95 V with limitations 0.80 V 0.80 V 1 A-port current source yes 1 mA yes 270 A no external pull-up 2 operating current <6.1 mA <1.9 mA <0.95mA standby current EN = LOW < 2 mA < 10 A max. < 10 A max. 1 The PCA9509 current mirrors do not shut down when the device is disabled allowing instant turn-on, but at the cost of the higher standby current. The PCA9509A and PCA9509P current mirrors are turned off when disabled for lowest standby power consumption, but sufficient delay (10 s) after enable is needed before resuming operation. 2 Operating currents do not include the current consumed by the external pull-ups on B-port or the external pull-ups on the A-port of the PCA9509P. 2. Features and benefits Bidirectional buffer isolates capacitance and allows 400 pF on port B of the device Voltage level translation from port A (0.8 V to 2.0 V) to port B (2.3 V to 5.5 V) Requires no external pull-up resistors on lower voltage port A Active HIGH repeater enable input disables current mirrors and current source to reduce standby power Open-drain port B inputs/outputs Lock-up free operation Supports arbitration and clock stretching across the repeater 2 Accommodates Standard-mode and Fast-mode I C-bus devices and multiple masters 2 Powered-off high-impedance I C-bus pins Operating supply voltage range of 0.8 V to 2.0 V on port A, 2.3 V to 5.5 V on port B All pins are 5 V tolerant with respect to ground pin 0 Hz to 400 kHz clock frequency Remark: The maximum system operating frequency may be less than 400 kHz because of the delays added by the repeater. ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101 Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA Packages offered: TSSOP8, XQFN8 PCA9509A All information provided in this document is subject to legal disclaimers. NXP B.V. 2018. All rights reserved. Product data sheet Rev. 3 17 May 2018 2 of 25