Reference Only Spec No. JETE243A-9105D-01 P 1/9 Chip Coil (Chip Inductors) DFE2HCAHJ0L REFERENCE SPECIFICATION Murata Standard SpecificationAEC-Q200 1.Scope This reference specification applies to DFE2HCAHJ0L, Chip Coil (Chip Inductors) for Automotive Electronic based on AEC-Q200. 2.Part Numbering (ex) DF E 2H CA H 1R0 M J 0 L Product Structure Dimension Applications Category Inductance Tolerance Dimension Other Packaging ID (LW) and (T) Characteristics 3.Rating Operating Temperature Range (Ambient temperature Self-temperture rise is not included) -40 to +110C (Product temperature Self- temperature rise is included) -40 to +150C Storage Temperature Range. -40 to +110C It can be considered for use ith DCDC conerters ith a maximum oltage of 40 or less. *3 Rated Current DC ESD (A) Inductance Resistance Customer Murata Le el Part Number Part Number (HBM) 1 Based on 2 Based on Tolerance Inductance change Temperature rise (H) Max. ( ) (%) DFE2HCAHR33MJ0L 0.33 0.021 5.8 4.9 DFE2HCAHR47MJ0L 0.47 0.025 5.1 4.5 DFE2HCAHR68MJ0L 0.68 0.031 4.4 3.6 20 1k DFE2HCAH1R0MJ0L 1.0 0.050 3.4 3.0 DFE2HCAH1R5MJ0L 1.5 0.074 2.9 2.3 DFE2HCAH2R2MJ0L 2.2 0.101 2.5 1.9 1: The saturation alloable DC current alue is specified hen the decrease of the initial Inductance alue at 30%. *2: Rated current (Based on Temperature rise) is the current alue at hich the product temperature rises to 40 hen direct current is applied to the inductor ith the product mounted on our designated board. 3: alue defined hen DC current flo s and Rated Current (Based on Inductance change) or hen DC current flo s and Rated Current (Based on Temperature rise) hicheer is smaller. 4. Testing Conditions (Standard atmospheric conditions) <Unless other ise specified> <In case of doubt> Temperature Temperature : 20 2C : Ordinary Temperature (5 to 35) Humidity : Ordinary Humidity (45 to 85% (RH)) Humidity : 655% (RH) Atmospheric Pressure : 86 to 106 kPa 5.Appearance and Dimensions 0.60.3 Unit Mass (Typical alue) 0.0324g no marking 2.50.2 1.2max. (in mm) MURATA MFG.CO., LTD 2.00.2 Reference Only Spec No. JETE243A-9105D-01 P 2/9 6. Electrical Performance No. No. Item Specification 6.1 Inductance Meet item 3 Measuring Equipment: KEYSIGHT 4284A or equialent (0.5) Measuring Frequency: 1MHz 6.2 DC Resistance Measuring Equipment: Resistance Hitester 3541(HIOKI) or equialent 6.3 Withstand machine: impulse testing machine InductanceMeet item 3 oltage applied oltage: 60-70 7. Q200 Requirement AEC-Q200 Rev.D issued June 1. 2010 AEC-Q200 Murata Specification / Deiation Stress Test Method No. 3 High Meet Table A after testing. 100012h at 1502 deg C Temperature Table A Set for 242hours Exposure at room temperature, Appearance No damage then measured. Inductance Change from ithin 10% an initial alue 4 Temperature Cycling 1000cycles -40 deg C for 30 min and 150 deg C for 30 min ith the transit period of 2min or less Measured ithin 242hours at room temperature. 7 Biased Humidity 100012h at 852 deg C, 85%RH Measured ithin 242hours at room temperature. 8 Operational Life Apply 1102 deg C 100012h Measured ithin 242h at room temperature. 10 Physical Dimension Measures using digital slide calipers and According to specification an optical microscope. MURATA MFG.CO., LTD