BLM15BB221SH1D

Reference Only Spec.No.JENF243A-9103L-01 P1/9 Chip Ferrite Bead BLM15SH1D Reference Specification AEC-Q200 1.Scope This reference specification applies to Chip Ferrite Bead BLM15 SH series for Automotive Electronics based on AEC- Q200. 2.Part Numbering (ex.) BL M 15 AG 102 S H 1 D (1) (2) (3) (4) (5) (6) (7) (8) (9) (1)Product ID (4)Characteristics (7)Category(for Automotive Electronics) (2)Type (5)Typical Impedance at 100MHz (8)Numbers of Circuit (3)Dimension (L) (6)Performance (9)Packaging (D:Taping) 3.Rating DC Resistance Rated Current* ( max.) (*1) (mA) (refer to below Impedance () ESD Rank Customer MURATA (at 100MHz)(*1) comment) 2 :2kV Part Number Part Number (refer to below comment) Initial Values 5A :8kV at 85C at 125C Values After Testing BLM15AG100SH1D 515 - 1000 0.05 0.10 BLM15AG700SH1D 40100 - 500 0.15 0.20 12025% - BLM15AG121SH1D 500 0.25 0.35 22025% - BLM15AG221SH1D 300 0.35 0.45 BLM15AG601SH1D 60025% - 300 0.60 0.70 BLM15AG102SH1D 100025% - 200 1.0 1.1 525% - BLM15BB050SH1D 500 0.08 0.15 BLM15BB100SH1D 1025% - 300 0.10 0.15 2225% - BLM15BB220SH1D 300 0.20 0.30 2 BLM15BB470SH1D 4725% - 300 0.35 0.45 BLM15BB750SH1D 7525% - 300 0.40 0.50 12025% - BLM15BB121SH1D 300 0.55 0.65 BLM15BB221SH1D 22025% - 200 0.80 0.90 47025% - BLM15BD471SH1D 200 0.60 0.70 BLM15BD601SH1D 60025% - 200 0.65 0.75 100025% - BLM15BD102SH1D 200 0.90 1.0 BLM15BD182SH1D 180025% - 200 1.4 1.5 BLM15PE300SH1D 3025% 2300 1400 0.035 0.050 BLM15PE600SH1D 6025% 1800 1100 0.060 0.075 BLM15PE800SH1D 8025% 1700 1000 0.070 0.085 BLM15PE121SH1D 12025% 1500 900 0.090 0.105 BLM15PE181SH1D 18025% 1200 700 0.140 0.155 5A BLM15PE221SH1D 22025% 1100 650 0.17 0.19 BLM15PE331SH1D 33025% 1000 580 0.21 0.23 BLM15PE471SH1D 47025% 750 450 0.35 0.37 BLM15PE601SH1D 60025% 700 420 0.40 0.42 * In case of BLM15PE series, as shown in the diagram below, derating is applied to the rated current based on the operating temperature. Operating Temperature : -55C to +125C Storage Temperature : -55C to +125C MURATA MFG.CO.,LTD. Reference Only Spec.No.JENF243A-9103L-01 P2/9 (*1) Standard Testing Conditions < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. (15 C to 35 C ) Temperature : 20C2 C Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa 4.Style and Dimensions 1.00.05 0.50.05 Equivalent Circuit 0.250.1 Resistance element becomes () dominant at high frequencies. :Electrode Unit Weight (Typical value) (in mm) 0.001g 5.Marking No marking. 6.Specifications 6-1.Electrical Performance No. Item Specification Test Method 6-1-1 Impedance Meet item 3. Measuring Frequency : 100MHz1MHz Measuring Equipment : KEYSIGHT4291A or the equivalent Test Fixture : KEYSIGHT16192A or the equivalent 6-1-2 DC Resistance Meet item 3. Measuring Equipment : Digital multi meter *Except resistance of the Substrate and Wire 6-2.Mechanical Performance (based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS) AEC-Q200 Rev.D issued June. 1 2010 AEC-Q200 Murata Specification / Deviation No. Stress Test Method 3 High 1000hours at 125 deg C Meet Table A after testing. Temperature Set for 24hours Table A Exposure at room temperature, Appearance No damage then measured. Impedance Change Within 30% (at 100MHz) DC Meet item 3. Resistance 4 Temperature Cycling 1000cycles Meet Table B after testing. -55 deg C to +125 deg C Table B Set for 24hours Appearance No damage at room temperature, Impedance Within 30% then measured. Change (BLM15PE (at 100MHz) Within60%) DC Meet item 3. Resistance 5 Destructive Per EIA469 No defects Physical Analysis No electrical tests 7 Biased Humidity 1000hours at 85 deg C, 85%RH Meet Table B after testing. Apply max rated current. MURATA MFG.CO.,LTD. 0.50.05