TC1272ARVNBTR

Obsolete Device TC1272/TC1273/TC1274 3-Pin Reset Monitors for 5V Systems Features General Description Precision V Monitor for 5.0V Systems The TC1272/TC1273/TC1274 are cost-effective CC system supervisor circuits designed to monitor V in 100 ms Minimum RESET, RESET Output CC digital systems and provide a reset signal to the host Duration processor when necessary. No external components Output Valid to V = 1.2V CC are required. Transient Immunity V CC The reset output is driven active within 20 s of V CC Small 3-Pin SOT-23 Package falling through the reset voltage threshold. RESET is No External Components maintained active for a minimum of 100 ms after V CC rises above the reset threshold. The TC1274 has an Applications active-high RESET output, while the TC1272 and Computers TC1273 have an active-low RESET output. The TC1272 and TC1274 each have a complimentary out- Embedded Systems put, while the TC1273 has an open-drain output. The Battery-Powered Equipment output of the TC1272 and TC1273 is valid down to V CC Critical P Power Supply Monitoring = 1.2V. The TC1274 is valid down to V = 1.8V. All CC three devices are available in a 3-Pin SOT-23 Package Type package. 3-Pin SOT-23 The TC1272/TC1273/TC1274 devices are optimized to line. reject fast transient glitches on the V CC Typical Application Circuit RESET 1 **(RESET) V CC TC1272 2 TC1273 3 GND V V TC1274 CC CC 1 RESET V 2 CC RESET Input Processor TC1272 **( ) is for TC1274 GND GND 3 2007 Microchip Technology Inc. DS21382C-page 1TC1272/TC1273/TC1274 Stresses above those listed underAbsolute Maximum Rat- 1.0 ELECTRICAL ing may cause permanent damage to the device. These are CHARACTERISTICS stress ratings only and functional operation of the device at these or any other conditions above those indicated in the Absolute Maximum Ratings operation sections of the specifications is not implied. Expo- sure to Absolute Maximum Rating conditions for extended Supply Voltage (V to GND) .............................+6.0V CC periods may affect device reliability. , RESET.......................... -0.3V to (V + 0.3V) RESET CC Input Current, V ..............................................20 mA CC Output Current, RESET, RESET........................20 mA 70C) Power Dissipation (T A 3-Pin SOT-23 (derate 4 mW/C above +70C) ................................................................230 mW Operating Temperature Range.............-40C to +85C Storage Temperature Range ..............-65C to +150C DC CHARACTERISTICS Electrical Specifications: Unless otherwise noted, T = -40C to +85C. Typical values are at T = +25C. A A Parameters Sym Min Typ Max Units Conditions Supply Voltage TC1272, TC1273 V 1.2 5.5 V Note 1 CC TC1274 V 1.8 5.5 V CC Output Voltage 0-500 A V V 0.5V V 0.1V V TC1272, TC1274 (Note 1) OH CC CC Output Current 2.4 Volts V = 5V TC1272 I 10 mA Note 2 CC OH V = 4V TC1274 I 8 mA CC OH Output Current 0.4 Volts I +10 30 mA Note 2, Note 5 OL Operating Current V < 5.5V: TC1272, TC1274 I 17 40 A Note 3 CC CC V < V < 5.5V: TC1273 I 17 40 A Note 3 CCTP CC CC V < V : TC1273 I 700 1200 A Note 3 CC CCTP CC V Trip Point (TC1272/3/4-5) V 4.50 4.62 4.75 V Note 1 CC CCTP-5 V Trip Point (TC1272/3/4-10) V 4.25 4.37 4.49 V Note 1 CC CCTP-10 V Trip Point (TC1272/3/4-15) V 4.00 4.12 4.24 V Note 1 CC CCTP-15 Output Capacitance C 9 pF OUT Internal Pull-Up Resistor R 36 9 k P AC Electrical Characteristics: T = -40C to +85C unless otherwise noted. Typical values are at T = +25C. A A RESET Active Time t 100 200 300 ms RST V Detect to RESET t 20 50 sV = 1V, Figure 4-2 CC RPD1 CC(LOW) TC1272, TC1273 V Detect to RESET - TC1274 t 20 50 sV = 1V, Figure 4-4 CC RPD2 CC(LOW) V Slew Rate t 300 s Figure 4-2, Figure 4-4 CC F (V (MAX) to V (MIN)) CCTP CCTP V Slew Rate t 0 ns Figure 4-1, Figure 4-3 CC R (V (MIN) to V (MAX)) CCTP CCTP V Detect to RESET t 100 200 300 ms Note 4, Figure 4-1 CC RPU1 TC1272, TC1273 V Detect to RESET - TC1274 t 100 200 300 ms Note 4, Figure 4-3 CC RPU2 Note 1: All voltages referenced to ground. 2: Measured with V 2.7 volts. CC 3: Measured with RESET output open for TC1272/TC1273 measured with RESET output open for TC1274. 4: t = 5 s. R 5: A 1 k external resistor may be required in some applications for proper operation of the microprocessor reset control circuit when using the TC1273. DS21382C-page 2 2007 Microchip Technology Inc.