MCP48FEB11-EUN

MCP48FEBXX 8-/10-/12-Bit Single/Dual Voltage Output Nonvolatile Digital-to-Analog Converters with SPI Interface Features Package Types Operating Voltage Range: MCP48FEBx1 MSOP - 2.7V to 5.5V - full specifications Single - 1.8V to 2.7V - reduced device specifications V SDI DD 1 10 Output Voltage Resolutions: 9 SCK 2 CS SDO V 3 8 - 8-bit: MCP48FEB0X (256 Steps) REF0 V 4 7 V SS OUT0 - 10-bit: MCP48FEB1X (1024 Steps) LAT0/HVC NC56 - 12-bit: MCP48FEB2X (4096 Steps) Rail-to-Rail Output MCP48FEBx2 MSOP Fast Settling Time of 7.8 s (typical) Dual DAC Voltage Reference Source Options: V DD SDI 1 10 - Device V DD SCK CS 9 2 (1) -External V pin (buffered or unbuffered) SDO REF V 3 8 REF V 7 V 4 SS - Internal Band Gap (1.22V typical) OUT0 (1) LAT0/HVC V 6 5 OUT1 Output Gain Options: Note 1: Associated with both DAC0 and DAC1 - Unity (1x) -2x General Description Nonvolatile Memory (EEPROM): - User-programmed Power-on Reset The MCP48FEBXX are Single- and Dual-channel 8-bit, (POR)/Brown-out Reset (BOR) output 10-bit, and 12-bit buffered voltage output setting, recall and device configuration bits Digital-to-Analog Converters (DAC) with nonvolatile memory and an SPI serial interface. - Auto Recall of Saved DAC register setting - Auto Recall of Saved Device Configuration pin, the device V or the internal band gap The V REF DD (Voltage Reference, Gain, Power-Down) voltage can be selected as the DACs reference voltage. When V is selected, V is connected Power-on/Brown-out Reset Protection DD DD internally to the DAC reference circuit. When the V REF Power-Down Modes: pin is used, the user can select the output buffers gain - Disconnects output buffer (High Impedance) to be 1 or 2. When the gain is 2, the V pin voltage REF - Selection of V pull-down resistors OUT should be limited to a maximum of V /2. DD (100 k or 1 k) These devices have an SPI-compatible serial interface. Low Power Consumption: Write commands are supported up to 20 MHz while - Normal operation: <180 A (Single), read commands are supported up to 10 MHz. 380 A (Dual) - Power-down operation: 650 nA typical Applications - EEPROM write cycle (1.9 mA maximum) Set Point or Offset Trimming SPI Interface: Sensor Calibration - Supports 00 and 11 modes Low-Power Portable Instrumentation - Up to 20 MHz writes and 10 MHz reads PC Peripherals - Input buffers support interfacing to Data Acquisition Systems low-voltage digital devices Motor Control Package Types: 10-lead MSOP Extended Temperature Range: -40C to +125C 2015 Microchip Technology Inc. DS20005429B-page 1MCP48FEBXX MCP48FEBX1 Device Block Diagram (Single-Channel Output) V DD Power-up/ Brown-out Control V SS Memory (32x16) SDI SPI Serial Interface Module DAC0 (Vol and NV) SDO and VREF (Vol and NV) Control Logic Power-down (Vol and NV) SCK (WiperLock Technology) Gain (Vol and NV) CS Status (Vol) VREF1:VREF0 V and PD1:PD0 DD Gain PD1:PD0 and V VREF1:VREF0 Band Gap BG Op (1.22V) Amp V OUT0 PD1:PD0 V + REF0 (1) - V PD1:PD0 SS V DD VREF1:VREF0 LAT0/HVC Note 1: If Internal Band Gap is selected, this buffer has a 2x gain. If the G bit = 1, this is a total gain of 4. DS20005429B-page 2 2015 Microchip Technology Inc. Resistor Ladder 1k 100 k