IDRIVE LITE

TM iDrive lite The intelligent 55W LED Driver USER MANUAL The iDrive lite is one of a family of devices specifically designed for the control and dimming of LED Fixtures. Product Overview Features TM Compact size and rugged construction with standard The powerful new iDrive lite LED driver is designed to 5-pin XLR DMX in/out connectors. optimize the performance of high power lighting fixtures using TM high power LEDs including Luxeon . Universal voltage input with standard IEC connector. TM The patented iDrive lite technology enables excellent colour TM Patented Colour Cool thermal management system to matching and 100% smooth dimming with precise DC current optimise and prolong the life of fixtures and LEDs. control combined with advanced automatic heat management system to enhance the long life of both fixtures and LED boards. TM The iDrive lite technology is licenced and patented in the UK and USA with Worldwide applications pending. The 55 Watt system provides a universal voltage input with both UL and CE approvals so you can install them in practically any Patented colour mixing 3 channel system. location. TM Simple 3 rotary switch interface sets DMX address and The iDrive lite has been designed to make installation simple controls all additional pre-set functions. and to save time by using standard power and DMX connectors TM with a unique user interface to control all iDrive lite functions. Smooth dimming control 0 - 100%. There are no complicated DIP switches High efficiency (>88%). The patented thermal control of attached LED boards, using our TM unique Colour Cool Technology, optimises your LED Long life and high reliability (50,000 hours). installation for any environment. LED lamp connection with 8 pin RJ45 connector. TM iDrive lite can be controlled by DMX512, or use the hundreds of pre-programmed settings to provide independent scenes, Short and open circuit protection. colour combinations and effects. Standalone mode (no DMX controller required) incorporating many static and dynamic colour functions and programmes. Self test functions. No binning of LEDs results in cost savings. Internal Thermal Protection. CE Approved colourcool IST Ltd is a certified Future Electronics is the solid state lighting division of IST Ltd Patented: USA 6,963,175.B2 LUXEON Solution Partner V.1.7 GB 2369730TM iDrive lite The intelligent 55W LED Driver Welcome to the iDrive lite, with a host of built in features and protection for your LED fixtures. The iDrive lite is designed to control fixtures containing between 18 and 36 RGB LED s. Please ensure that the LED fixture is plugged into the iDrive RJ45 connector before the mains is switched on, this is important since the system will perform a diagnostic scan of the LED fixture when powered up. The diagnostic scan will test for two functions. 1.Open or short circuits in the LED fixture and wiring. If this is detected the faulty channel will be isolated. The RED LED wiring fault indicator will illuminate to confirm this. The iDrive should be turned off at the mains and the fault rectified before powering up the system again. 2. The second scan will look for a thermistor on the LED fixture, as recommended in the wiring specification (page 4). If a thermistor is found the thermal feedback protection will be activated in the iDrive. Both these scans take less than 1 second to perform and only take place on initial power up of the system. Mains Indicator - Indicates power onto the x100 x10 x1 iDrive DMX Indicator - When the rotary switches are set to a DMX address i.e. between 001 and 510, this indicator will flash until the iDrive receives a DMX input via the DMX 5-pin XLR input. Once a DMX signal is received, the amber indicator stops flashing and stays permanently on. Wiring Fault Indicator - The iDrive has short/open circuit protection. In the event of the DMX Wiring Fault LED fixture being incorrectly wired, the indicator Indicator Indicator will be permanently on until the fault in the LED fixture has been corrected. Mains Indicator The iDrive uses DMX 512A - the latest ESTA DMX standard, using isolated 5-pin XLR connections for both input and output. The iDrive can be used in DMX mode or stand alone mode. For DMX Settings The rotary switches should be set to between 001 and 510. Normally address 0.0.1 is sufficient for a 3 channel and master DMX controller. For Stand Alone Settings The iDrive contains many pre-set programmes. 600 - 636 - This setting provides 36 different preset colours - 636 being a white setting, i.e. all LEDS full on. 700 - 799 - These are the cross fade settings with DMX IN DMX OUT different speed functions. 800 - 819 - Cycle Wash Pre-set. There are two preset cyclic washes, either clockwise or anti-clockwise with speed control colourcool IST Ltd is a certified Future Electronics is the solid state lighting division of IST Ltd Patented: USA 6,963,175.B2 LUXEON Solution Partner V.1.7 GB 2369730