62M15-M0-020CH

Optical and Mechanical Encoders Specifications are subject to change. Please refer to the current datasheet on www.grayhill.com for the most current published specifications for this product. Optical Encoders SERIES 62M Magnetic Detent FEATURES Applications Ultra Smooth Magnetic Detent Medical 3 Million Rotational Cycles, Audio Ten Times the Life of a Instrumentation Mechanical Detent System Optional Integrated Pushbutton Available in 24 Positions Choice of Cable Lengths DIMENSIONS in inches (and millimeters) Stripped Version Pinned Cable Version Version DETERMINED DETERMINED BY PART NO. BY PART NO. RECOMMENDED PANEL CUTOUT SWITCH SCHEMATIC 6 POWER (5V) 2 R* .161.002 OUTPUT A 5 4,090,05 .380.003 R* 9,650,07 OUTPUT B 4 PUSHBUTTON 3 2 PUSHBUTTON GROUND 1 .057.002 1,450,05 *EXTERNAL 2.2k PULL-UP RESISTORS REQUIRED FOR OPERATION. Grayhill, Inc. 561 Hillgrove Avenue LaGrange, Illinois 60525-5997 USA Phone: 708-354-1040 Fax: 708-354-2820 www.grayhill.comOptical and Mechanical Encoders Specifications are subject to change. Please refer to the current datasheet on www.grayhill.com for the most current published specifications for this product. Optical Encoders WAVEFORM AND TRUTH TABLE Clockwise Rotation HIGH OUTPUT Position Output B Output A A LOW 1 2 HIGH OUTPUT 3 B LOW 4 1 2 3 4 5 6 Indicates logic high blank indicates logic POSITION NUMBER low. Code repeats every 4 positions. SPECIFICATIONS Rotational Torque: H=1.70 1.00 in-oz, Environmental Specifications Materials and Finishes 0 0 Operating Temperature Range: -40 C to 85 M=1.25 0.75 in-oz, L=0.75 0.5 in-oz Bushing: Zinc Diecast, Cadmium Plated per C Mounting Torque: 15 in-lb maximum QQP-416, Class II, Type II 0 0 Storage Temperature Range: -55 C to 100 C Shaft Pull-Out Force: 45 lbs minimum Insert Molded into 25% Glass Reinforced Humidity: 96 hours at 90-95% humidity Shaft Push-Out Force: 45 lbs minimum Nylon Zytel FR-50 0 Terminal Strength: 15 lbs minimum terminal at 40 C Shaft: NdFeB XE-3594 over Aluminum Mechanical Vibration: Harmonic motion with pull-out force for cable or header termination Cable: Copper Standard with Topcoat in PVC amplitude of 15 g, within a varied frequency of Solderability: 95% free of pin holes and Insulation (Cabled Versions Only) 10 to 2000 Hz voids Connector: PA4.6 with Tin Plated Copper Mechanical Shock: Alloy (Cable/Connector Versions) Test 1: 100 g for 6 ms half-sine wave with a Pushbutton Electrical and Mechanical Solder: Sn/Ag/Cu, Lead Free, No Clean velocity change of 12.3 ft/sec Mounting Hex Nut: Cadmium over 1/2 Hard Specifications Test 2: 100 g for 6 ms sawtooth wave with a Brass Rating: 10 mA at 5 Vdc velocity change of 9.7 ft/sec Lockwasher: 8-18 Stainless Steel, Passivate Contact Resistance: <10 ohms Finish Life: 3 million actuations minimum Rotary Electrical and Contact Bounce: <4 ms make,<10 ms break Pin Header: Hi-Temp Glass Filled Thermo- plastic UL94V-0, Phosphor Bronze (Pinned Actuation Force: 2=20075 grams, Mechanical Specifications 3=30090 grams, 4=510150 grams Versions Only) Operating Voltage: 5.00.25 Vdc Shaft Travel: .025 .010 inches Supply Current: 30 mA maximum at 5 Vdc This product series is ROHS Compliant. Output: Open collector phototransistor, external pull-up resistors are required. Output Code: Two-bit quadrature, channel 0 A leads channel B by 90 electrically during clockwise rotation of the shaft Logic Output Characteristics: Logic high signal shall be no less than 3.0 Vdc Logic low signal shall be no greater than 1.0 Vdc Minimum Sink Current: 2.0 mA Power Consumption: 150 mW maximum Mechanical Life: 3 million rotational cycles of operation. One cycle is a rotation through all positions and a full return Series 0 Angle of Throw: 15 = 15 for code change and 24 detent positions Rotational Torque: H=High Torque (1.70 in-oz), M=Medium Torque (1.25 in-oz), L=Low Torque (0.75 in-oz) Pushbutton Option: 0=Non-Pushbutton, 2 = 200 grams, 3 = 300 grams, 4 = 510 grams 62MXX-XX-040X Termination: CH =.100 Cable with Connector, SH = Cable with Stripped-End, PH = Pin Header Cable Termination: 040 = 4.0in. Cable is terminated with Amp Connector P/N 3-640442-6. See Amp Mateability Guide for mating connector details. *Eliminate cable length if ordering pins (Ex: 62M22-42-PH) Grayhill, Inc. 561 Hillgrove Avenue LaGrange, Illinois 60525-5997 USA Phone: 708-354-1040 Fax: 708-354-2820 www.grayhill.com