I5S

i5s AC CURRENT CLAMP 600 V CAT III SERIAL NUMBER Safety Specifications Single Insulated Category Rating: CAT III 600 V per IEC/EN61010-1, Pollution Degree 2 Current Carrying EMC: EN 61326-1, FCC for emission and immunity Conductor Complies with U.S. and Canadian Standards CAN/CSA C22.2 No. 61010-1-04 and ) No. 61010-2-032-04 UL61010-1 Release nd IEC 61010-1 2 Edition IEC 61010-02-032 P Button i5s AC Current Clamp Load Direction Arrow Electrical Specifications Instruction Sheet Reference Conditions: 23 5 C, 20 to 75 % RH conductor centered in jaw opening no DC component no adjacent conductor. Measurement Range: 10 mA to 6 A Introduction Output: 400 mV/A The i5s (hereafter called the Current Clamp) is compatible with any instrument that can accept Accuracy (48 Hz to 65 Hz): a standard BNC connector and is capable of ac millivolt measurements the Current Clamp can also be used with digital multimeters using a BNC-to-dual banana plug adapter. The Current 10 mA to 1 A 1% + 5 mA Clamp produces an output of 400 mV ac per 1 A ac input level. 1 A to 5 A 1% Tactile Barrier Phase Shift (48 Hz to 65 Hz): Contacting Fluke 10 mA to 100 mA Unspecified To contact Fluke, call one of the following telephone numbers: 100 mA to 5 A 4 BNC Connector USA: 1-888-44-FLUKE (1-888-443-5853) Crest Factor: 3, add 0.7 % to accuracy Canada: 1-800-36-FLUKE (1-800-363-5853) Typical Bandwidth: 40 Hz to 5 kHz Banana Europe: +31 402-675-200 Working Voltage: 600 V ac rms, in compliance with EN61010 Japan: +81-3-3434-0181 Plug Singapore: +65-738-5655 Common Mode Voltage: 600 V ac rms from earth ground, in compliance with EN61010 Anywhere in the world: +1-425-446-5500 Input Load Impedance (of host instrument): >1 M in parallel with up to 47 pF USA Service: 1-888-99-FLUKE (1-888-993-5853) Maximum Non-destructive Current: 70 A cab01f.eps Or, visit Fluke s Web site at www.fluke.com. Duty Cycle: 0.01 A to 6 A continuous Figure 1. i5s Setup To register your product, visit register.fluke.com Influence of Adjacent Conductor: 15 mA/A ( 50/60 Hz) Safety Information Influence of Conductor Position in Jaw Opening: 0.5 % of reading ( 50/60 Hz) Maintenance XW Read First: Safety Information XW Warning General Specifications To ensure safe operation and service of the Current Clamp, follow these instructions: To avoid possible electric shock or personal injury: Read the operating instructions before use and follow all safety instructions. Output Cable Length: 2.5 m Use the Current Clamp only as specified in the operating instructions, otherwise the Maximum Conductor Size: 15 mm Before each use, inspect the Current Clamp. Look for cracks or missing portions of the clamps safety features may not protect you. Storage Temperature: -20 C to 60 C clamp housing and output cable insulating cover and for loose or weakened components. Adhere to local and national safety codes. Individual protective equipment must be Operating Temperature: 0 C to 50 C Pay particular attention to the insulation surrounding the clamp jaws. used to prevent shock and arc blast injury where hazardous live conductors are Relative Humidity: 10 C to 30 C: 85 % exposed. Do not use a damaged Current Clamp. If a clamp is damaged, tape it shut to prevent 30 C to 40 C: 75 % Do not hold the Current Clamp anywhere beyond the tactile barrier, see Figure 1. unintended operation. A damaged clamp under warranty will be promptly repaired or 40 C to 50 C: 45 % Before each use, inspect the Current Clamp. Look for cracks or missing portions of the replaced (at Flukes discretion) and returned at no extra charge. Temperature Coefficient: 0.01 % X (specified accuracy)/ C clamp housing or output cable insulation. Also look for loose or weakened (< 18 C or > 28 C) If the Current Clamp does not work or perform properly, use the following steps to help isolate components. Pay particular attention to the insulation surrounding the jaws. the problem: Altitude: Operating: 2000 m Non-operating: 12000 m Never use the Current Clamp on a circuit with voltages higher than 600 V CAT III. 1. Inspect the jaw mating surface for cleanliness. If any foreign material is present, the jaw will Dimensions: 116 x 43 x 23 mm CAT III equipment is designed to protect against transients in equipment in fixed not close properly and measurement errors will result. Weight: 200 g equipment installations, such as distribution panels, feeders and short branch circuits, 2. Verify that the function selection and range on the Multimeter are correct and adjusted to the and lighting systems in large buildings. sensitivity of the Current Clamp. The Clamp is designed for use on insulated conductors only. Use extreme caution when Instrument Compatibility working around bare conductors or bus bars. Contact with the conductor could result in The Current Clamp is compatible with any Fluke Multimeter or any other current measurement electric shock. Cleaning device that has the following features: Use caution when working with voltages above Periodically wipe the case with a damp cloth and mild detergent. BNC or Banana inputs 60 V dc or 30 V ac rms. Such voltages pose a shock hazard. W Caution Input accuracy of 1 % or better to take full advantage of the accuracy of the Current Clamp. Input impedance of > 1 M in parallel with up to 47 pF To avoid damaging the Current Clamp, do not use abrasives or solvents to Symbols clean the clamp. Note Open the jaws and wipe the magnetic pole pieces with a lightly oiled cloth. Do not allow rust or Do not apply around or remove from HAZARDOUS LIVE conductors. Current input impedance on the Fluke 430 Series Three-Phase Power Quality Analyzer is - corrosion to form on the magnetic core ends. < 1 M , but it has a special calibration setting for the i5s to achieve full accuracy. Product is protected by double insulation. T LIMITED WARRANTY AND LIMITATION OF LIABILITY Measurement Considerations This Fluke product will be free from defects in material and workmanship for one year from the Risk of Danger. Important information. See Instruction Sheet. Center the conductor inside the Current Clamp jaw. date of purchase. This warranty does not cover fuses, disposable batteries, or damage from W accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or Make sure the Current Clamp is perpendicular to the conductor. handling. Resellers are not authorized to extend any other warranty on Flukes behalf. To obtain For optimal reading, make sure the conductor is centered in the jaws of the Current Risk of Electric Shock. X service during the warranty period, contact your nearest Fluke authorized service center to obtain Clamp. return authorization information, then send the product to that Service Center with a description Observe the following guidelines when making measurements: Canadian Standards Association has certified that the product meets applicable U.S. of the problem. ) Avoid taking measurements close to other current-carrying conductors. THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR and Canadian Standards. A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY Operation SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING Conforms to relevant European Union directives. P FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or To use the Current Clamp, refer to Measurement Considerations and Figure 1: limitation of an implied warranty or of incidental or consequential damages, this limitation of 1. If necessary, add a dual banana plug to BNC adapter to the i5s BNC connector. liability may not apply to you. 2. Connect the clamp cable to the instrument. If using an adapter, use the common and Fluke Corporation Fluke Europe B.V. volts inputs of the meter and switch it on. P.O. Box 9090 P.O. Box 1186 3. Make sure the measurement instrument is set to the proper range. Everett, WA 98206-9090 5602 BD Eindhoven 4. Make sure the arrows on each side of the Current Clamp face towards the load of the U.S.A. The Netherlands circuit. 5. Open the Current Clamp jaw by pushing the release button toward the jaw until the latch has cleared the barrier, then press down to open the jaw. 6. Connect the Current Clamp jaws around the insulated conductor to be measured and 11/99 PN 2458104 May 2005 release the button. Ensure that the release button has returned to the original position to resume the circuit testing. 2005 Fluke Corporation. All rights reserved. XW Warning All product names are trademarks of their respective companies. To avoid shock or personal injury, keep fingers behind the tactile barrier, see Figure 1. X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Clamp Multimeters & Accessories category: Click to view products by Fluke manufacturer: Other Similar products are found below : I800 FLUKE 1630-2 ZAPDUMOD-03 ZARKMS-01-99 UT233 TESTO 770-3 0590 7703 AX-3550 AX-M266C BM079 BM089 BM157 BM162 BM197 KEW2210R FLUKE 80I-110S FLUKE I200 FLUKE I200S FLUKE I3000FLEX-24 FLUKE I310S FLUKE I400 CIE600 TESTO 770-2 0590 7702 34194A KEW2433R KEW8112 FLUKE 772 380976-K MA3110 MA440 MA443 MA445 FLUKE-374 FC TA74 AMP-320 CM55 CM46 I200 ACD-6 PRO FLUKE-1630-2FC I410 CM44 CM42 FLK-A3000 FC FLUKE-376 FC ACD-14-PRO MA610 F201 F205 MA193 (250 MM) DIGIFLEX 4000A 350MM