ELM040W-1000-38

TROPO 15W Dimmable LED Driver Features TROPO switch mode power supply technology is designed to generate one constant current output from an AC input, and work with industry standard lighting controls in dimming applications. 120VAC and 230VAC Inputs Available Output current availability 0.35A-1.5A. Consult Factory for customized programming Operates with Industry Standard Dimmers Compact Encapsulated Assembly Active Power Factor Correction Output Over-Voltage, Over-Current and Short-Circuit 12-34 W ELM030 Protection and Auto Recovery High Temperature Operation (up to 90C case) 34-40 W ELM040 UL Approved, ENEC Approved, CE Mark Long Life ROHS Compliant ELM050 41-53 W Constant-Current LED Drivers with Dual Dimming: TROPO is designed for powering LED luminaries with standard lighting controls. The modules operate with: Standard Light Switches Forward/Reverse-Phase and 0 - 10 V Triac based Incandescent Dimmers (Standard phase leading edge) Electronic Low Voltage Dimmers (Reverse Phase trailing edge) Input& Max.&Output& Output& Output& Max.&Case& Power& Dimming& Dimming& Efficiency &THD Voltage Power Voltage Current Temperature Factor Method Range TROPO is ideal for installations requiring dimmable Class 2 outputs such as: 90C$ ForwardKPhase, 120$&$277$ 10$to$56$ 350$mA$to$ $84%$ 10$K$100% 50$W (measured$at$ <$20% >$0.9 ReverseKPhase Vac$nominal Vdc 1.75$A$CC typical (%$of$$Iout) Commercial Lighting Residential Lighting the$hot$spot) &$0$K$10V CC: Constant Current The following diagram depicts a typical installation utilizing the TROPO: PRODUCT DESCRIPTION The ELM030/040/050 series of LED drivers is compliant TRIAC Dimmer + Dim with industry standard phase-cut dimmers, both forward- Dimmer - Dim Dimming range down to less then phase and reverse-phase, and 010V dimmers, making it Triac 10% nominal output current + LEDs ideally suited for both new construcUons and retrot Based 0-10 V Output current does not terminate Dimmer Dimmer during off time of dimmer applicaUons, in ResidenUal or Commercial markets. Output Current factory settable up to 1.5A ELM030 TROPO Multiple Drivers / LED Assemblies may be connected to a single dimmer FEATURES Facilitates compliance with Energy NOT RECOMMENDED FOR NEW DESIGNS. For new - LEDs Star ratings for LED luminares designs, use the ESM series TYPICAL APPLICATION DIAGRAM CompaUble with TRIAC (forward-phase or leading-edge) / ELV (reverse-phase or trailing-edge) and 010 V dimmers 120 and 277 Vac nominal input voltage ProtecUons: output open load, over-current and short- circuit (hiccup), and over-temperature with auto recovery Conducted and radiated EMI: FCC CFR Title 47 Part 15 compliant with Class B at 120 Vac and Class A at 277 Vac Enables ENERGY STAR and DLC (DesignLight ConsorUum) luminaire compliance CFL ballast rectangular metal case IP20-rated case with silicone-based poang 90C maximum case hot spot temperature 50,000 hours lifeUme Class 2 power supply METAL CASE: Double-insulated power supply between input and ELM030: 110 x 60 x 26 mm (4.33 x 2.36 x 1.02 in) output (class II) ELM040/050: 127 x 70 x 28 mm (5 x 2.76 x 1.1 in) Worldwide safety approvals APPLICATIONS Troers Purple: + Dim Signal Downlights Low Bay lighUng White: Neutral Grey: - Dim Signal LED Commercial lighUng Red: + LEDs DRIVER Architectural lighUng Black: Line Black: - LEDs 5 WIRING DIAGRAM ELM030/040/050 Data Sheet 1 ERP - ENERGY RECOVERY PRODUCTS December 7, 2014 Rev. F 12-34 W ELM030 34-40 W ELM040 ELM050 41-53 W Constant-Current LED Drivers with Dual Dimming: Forward/Reverse-Phase and 0 - 10 V 1 - INPUT SPECIFICATION (@25C ambient temperature) Units Minimum Typical Maximum Notes 90 120 132 Input4Voltage4Range4(Vin) Vac 240 277 305 Input4Frequency4Range Hz 57 60 63 At1nominal1input1voltage1and1nominal1LED1load1 Power4Factor4(PF) 0.9 >10.9 (nominal1Vout) 0.441A1@11201Vac Input4Current4(ELM030) A D D 0.191A1@12771Vac 0.661A1@11201Vac Input4Current4(ELM040/050) A D D 0.291A1@12771Vac Inrush4Current A 101A1peak At1any1point1on1the1sine1wave1and125C Leakage4Current A 2501A1@112011Vac Measured1per1IEC60950D1 Input4Harmonics Complies1with1IEC61000D3D21for1Class1C1equipment !At11nominal1input1voltage1and1nominal1LED1load Total4Harmonics4Distortion4 20% !Complies1with1DLC1(DesignLight1Consortium)1 (THD) 111technical1requirements1v2.0 Measured with nominal input voltage, a full sinusoidal Efficiency D 84% D wave form without dimmer connected. Models with full1load1ratings1of120W1have1an1efficiency1of175%. Isolation Meets1UL60950D11for1class1II1reinforced/double1insulation1power1supply 2 - OUTPUT SPECIFICATION (@25C ambient temperature) Units Minimum Typical Maximum Notes Vdc 10 56 Output4Voltage4(Vout) See*ordering*information*for*details mA 350 1750 Output4Current4(Iout) See*ordering*information*for*details Output4Current4Regulation % :5 2.5 5 Includes*AC*line*voltage,*load,*and*current*set*point*variations The driverdoes notoperate outsideof theregulation requirements for : : 10 more than500ms duringpower onwithnominal LED load andwithout* dimmer. Output4Current4Overshoot % The driverdoes notoperate outsideof theregulation requirements for : : 15 more than 500 ms during power on with nominal LED load and with* dimmer. !Measuredwith a nominalLEDload andnominal input voltage with no <*25%*peak:to:peak*of*rated*output* Ripple4Current dimming. current*for*each*model !Calculated*in*accordance*with*the*IES*Lighting*Handbook,*9th*edition 10% 100% Dimming4Range4(%4of4Iout) The*dimming*range*will*be*dependent*on*each*specific*dimmer. The outputis within the regulation band within 1 secondof AC voltage StartAup4Time s 1 being*applied.*This*is*measured*with*no*incandescent*dimmer*attached,* at*nominal*input*voltage*and*at*nominal*load. Output4Controls The +Dim/:Dim signal pins can be used to adjust theoutput setting via a standard commercialwall dimmer,an +Dim4Signal,4ADim4Signal external control voltage source (0 to 10 Vdc), or a variable resistor when using the recommended number of LEDs.*The*dimming*input*permits*10%*to*100%*dimming.*The*voltage*on*the*+Dim*input*must*be**10V. SaveEnergy@ERPpowerllc.com 2 www.ERPpowerllc.com