ESM020W-0440-25-SS-F1B

TROPO 15W Dimmable LED Driver Features TROPO switch mode power supply technology is designed to generate one constant current output from an AC input, and work with industry standard lighting controls in dimming applications. 120VAC and 230VAC Inputs Available Output current availability 0.35A-1.5A. Consult Factory for customized programming Operates with Industry Standard Dimmers Compact Encapsulated Assembly Active Power Factor Correction 10-20 W ESM020 Output Over-Voltage, Over-Current and Short-Circuit Protection and Auto Recovery 21-30 W ESM030 High Temperature Operation (up to 90C case) 31-40 W UL Approved,ESM ENEC 0Approved,40 CE Mark Long Life 41-50 W ESM050 ROHS Compliant 51-60 W ESM060 Tri-Mode Dimming (0-10 V & TRIAC/ELV) TROPO is designed for powering LED luminaries with standard lighting controls. The modules operate with: Standard Light Switches Constant Current LED Drivers with Fast Startup Time Triac based Incandescent Dimmers (Standard phase leading edge) Electronic Low Voltage Dimmers (Reverse Phase trailing edge) Max.& Input& Output& Output& Max.&Case& Power& Dimming& Dimming& Startup& TROPO is ideal for installations requiring dimmable Class 2 outputs such as: Output& Efficiency &THD Voltage Voltage Current Temperature Factor Method Range Time Power 90 to 305 280 mA 90C ForwardJPh as e,Commercial Lighting Residential Lighting 19 to 56 87% 1 J 100% Vac 60 W to 1.4 A (measured at < 20% > 0.9 ReverseJPhase 300 ms Vdc typical (% of Iout) maximum CC the hot spot) & 0 J 10V CC: Constant Current The following diagram depicts a typical installation utilizing the TROPO: PRODUCT DESCRIPTION TRIAC Dimmer + Dim Dimmer The ESM series of LED drivers is ideally suited for LED - Dim Dimming range down to less then lighting applications in office, commercial and residential. Triac 10% nominal output current + LEDs 0-10 V Based Output current does not terminate These devices are compatible with most industry standard Dimmer Dimmer during off time of dimmer phase-cut wall-based dimmers, both forward-phase Output Current factory settable up to 1.5A ESM (leading-edge) and reverse-phase (trailing edge), and 0-10V TROPO Multiple Drivers / LED Assemblies wall-based dimmers and offer deep dimming from 100% may be connected to a single series downto1%. dimmer Facilitates compliance with Energy - LEDs Star ratings for LED luminares FEATURES APPLICATION DIAGRAM Compatible with TRIAC (forward-phase or leading-edge) / ELV (reverse-phase or trailing-edge) and 0-10 V dimmers Forward-phase and reverse-phase dimming only at 120 Vac Linear 0-10V dimming transfer function: 10V=100%, 1V=10%, 0.1V=1% Optional remote off function causes the output current and output voltage to switch off when the 0-10V dimming wires are shorted with each other. Lifetime: 85,500 hours at 70 C case hot spot temperature (39 C ambient temperature) for ESM050W-1200-42 (50 W) Protections: output open load, over-current and short-circuit (hiccup), and over-temperature with auto recovery Conducted and radiated EMI: Compliant with FCC CFR Title 47 Part 15 Class B (120 Vac)/Class A (277 Vac) and EN55015 (CISPR 15) at 220/230/240 Vac METAL CASE: Enables ENERGY STAR and DLC (DesignLightConsortium) L 110 x W 60 x H 26 mm luminaire compliance (L 4.33 x W 2.36 x H 1.02 in) IP64-rated case with silicone-based potting 90 C maximum case hot spot temperature Class 2 power supply Purple: + Dim Double-insulated power supply between input and output White: Neutral Grey: -Dim (class II) LED Worldwide safety approvals Red: + LEDs DRIVER Black: Line Black: -LEDs APPLICATIONS Recessed lighting (downlights) WIRING DIAGRAM Commercial & Residential lighting 5 Office lighting ESM Series Data Sheet 1 ERP -ENERGY RECOVERY PRODUCTS November 2, 2015 -Rev. B10-20 W ESM020 21-30 W ESM030 31-40 W ESM040 41-50 W ESM050 51-60 W ESM060 Tri-Mode Dimming (0-10 V & TRIAC/ELV) Constant Current LED Drivers with Fast Startup Time 1 - INPUT SPECIFICATION ( 25 C ambient temperature) Units Minimum Typical Maximum Notes 120/220/230/ The0rated0output0current0for0each0model0is0achieved0at0 Input4Voltage4Range4(Vin) Vac 90 305 240/277 Vin001080Vac0and0at0Vin001980Vac,0at0nominal0load. Input4Frequency4Range Hz 47 60 63 Power4Factor4(PF) 0.9 >00.9 At0nominal0input0voltage0and0with0nominal0LED0voltage Inrush4Current Meets0NEMAS4100requirements At0any0point0on0the0sine0wave0and025C 2500A0 01200Vac Leakage4Current A 5000A0 02300Vac Measured0per0IEC60950S1 6000A0 02770Vac Input4Harmonics Complies0with0IEC61000S3S20for0Class0C0equipment At0nominal0input0voltage0and0nominal0LED0voltage Total4Harmonics4Distortion4 20% Complies0with0DLC0(DesignLight0Consortium)0technical0 (THD) 00requirements Measured with nominal input voltage, a full sinusoidal Efficiency % S 87% S wave0form0and0without0dimmer0connected Isolation Meets0UL60950S10for0class0II0reinforced/double0insulation0power0supply 2 - OUTPUT SPECIFICATION ( 25 C ambient temperature) Units Minimum Typical Maximum Notes Output4Voltage4(Vout) Vdc 19 56 See*ordering*information*for*details See*ordering*information*for*details Output4Current4(Iout) mA 280 1400 The*rated*output*current*for*each*model*is*achieved*at*Vin**108*Vac* and*at*Vin**198*Vac,*at*nominal*load. Output4Current4Regulation % D5 2.5 5 Includes*AC*line*voltage,*load,*and*current*set*point*variations The*driver*does*not*operate*outside*of*the*regulation*requirements*for* Output4Current4Overshoot % D D 10 more*than*500*ms*during*power*on*with*nominal*LED*load*and* without*dimmer. Measured*at*nominal*LED*voltage*and*nominal*input*voltage*without* *33%*of*rated*output*current*for*each* Ripple4Current dimming. model Calculated*in*accordance*with*the*IES*Lighting*Handbook,*9th*edition. Dimming4Range4(%4of4Iout) % 1 100 The*dimming*range*will*be*dependent*on*each*specific*dimmer. 300 With*nominal*LED*voltage*and*without*dimmer*attached With nominalLED voltage, with anapproveddimmer attached (see list StartEup4Time ms 400 of approved dimmers in page 7) and at the full dimming conduction angle Output4Controls The +Dim/DDimsignal pins can be used to adjust the output setting via a standard commercialwall dimmer,an +Dim4Signal,4EDim4Signal external*control*voltage*source*(0*to*10*Vdc),*or*a*variable*resistor*when*using*the*recommended*number*of*LEDs.* The*dimming*input*permits*1%*to*100%*dimming. SaveEnergy ERPpowerllc.com 2 www.ERPpowerllc.com