PI3B16233AE

1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 PI3B162332123456789012 1 2345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012 12345678901 2 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 3.3V, 16-Bit to 32-Bit FET Mux/DeMux NanoSwitch Features Description 5-ohm Switch Connection Between Two Ports Pericom Semiconductors PI3B16233 is a 16-bit to 32-bit mux/demux switch. This device can be used for memory bank interleaving. The Near-Zero Propagation Delay PI3B16233 can be used as two 8-bit to 16-bit multiplexers or as one Fast Switching Speed: 4.5ns (max.) 16-bit to 32-bit multiplexer. Ultra -Low Quiescent Power (0.2mA typ.) Two select inputs (SEL1 and SEL2) control the data flow. When the Ideal for notebook applications. TEST inputs are asserted HIGH, the A port is connected to both the Industrial Operating Temperature: 40C to 85C B1 and the B2 ports. Package (Pb-free & Green available): 56-pin 240-mil wide plastic TSSOP (A) 56-pin 300-mil wide plastic SSOP (V) Block Diagram Pin Configuration 30 SEL 1 1A 1 56 1B1 27 TEST 1 2 55 2B1 1B2 2B2 3 54 2A 3A 4 53 3B1 4B1 5 52 3B2 4B2 6 51 4A One of Eight Channels 155 5A 5B1 1A 1B2 7 50 SW 6B1 8 49 5B2 56 6B2 9 48 6A 1B1 SW 7A 7B1 10 47 29 SEL SW 2 8B1 11 46 7B2 28 TEST 2 8B2 8A 12 45 13 44 AB GND GND VCC VCC 14 43 9A 9B1 15 42 S 10B1 9B2 16 41 One of Eight Channels 15 41 10B2 17 40 10A 9A 9B2 SW 11A 39 11B1 18 42 12B1 11B2 19 38 SW 9B1 12B2 20 37 12A 13A 13B1 21 36 14B1 13B2 22 35 Function Table 14A 14B2 23 34 Inputs 15A 24 33 15B1 Function STEL TES 16B1 15B2 25 32 16B2 26 31 16A LL A = B1 TEST1 SEL1 27 30 HL A = B2 28 29 TEST2 SEL2 XH A = B1 and A = B2 PS8171F 05/09/06 1 07-0010PI3B16233 3.3V, 16-Bit to 32-Bit FET Mux/DeMux NanoSwitch 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ...................................................... 65C to +150C Note: Stresses greater than those listed under MAXIMUM RAT- Ambient Temperature with Power Applied ...................... 40C to +85C INGS may cause permanent damage to the device. This is a Supply Voltage Range ....................................................... 0.5V to +4.6V stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational DC Input Voltage ............................................................... 0.5V to +4.6V sections of this specification is not implied. Exposure to DC Output Current ........................................................................ 120mA absolute maximum rating conditions for extended periods may affect reliability. Power Dissipation ............................................................................. 0.5W DC Electrical Characteristics (Over the Operating Range, T = 40C to +85C, V = 3.0V to 3.6V) A CC (1) (2) PnarametersDsescriptio Test Condition M.in. TypMsax. Unit VIlnput HIGH VoltageG0uaranteed Logic High Leve 2. IH V VIlnput LOW VoltageG5uaranteed Logic Low Leve 80. 0. IL IIVnput HIGH Current = Max., V = V 1 IH CC IN CC IIVnput LOW Current = Max., V =DG1N A IL CC IN IH0igh Impedance Output Current A, B V 1 OZH CC VCVlamp Diode Voltage = Min., I=718mA 20. V1. IK CC IN (3) R Switch ON Resistance V = Min., V = 0.0V, I = 48mA or 64mA 5 8 ON CC IN ON V = Min., V = 2.4V, I = 15mA 10 15 CC IN ON Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 3.3V, T = 25C ambient and maximum loading. CC A 3. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. Capacitance (T = 25C, f = 1 MHz) A (1) ParametersDsescription T.est Condition Tsyp Unit C Input Capacitance 3.0 IN V = 0V pF IN C A/B Capacitance, Switch On 25.0 ON Notes: 1. This parameter is determined by device characterization but is not production tested. PS8171F 05/09/06 07-0010 2