81552101

W W W.CROUZET-CONTROL.COM 40 PNEUMATICS PRODUCTS W W W.CROUZET-CONTROL.COM 41 PNEUMATICS PRODUCTS Vacuum handling components Sur le principe du Venturi Facilement raccordable Also available in ATEX version for use in poten- tially explosive atmospheres in accordance with 94/9/EC Directive Part numbers Vacuum generators 81 535 301 81 545 001 81 545 005 PNEUMATIC Sub-base mounting Plug-in Plug-in LOGIC COMPONENTS Characteristics Push-in connectors for Male/Female/Female (MFF) - 4 mm - semi-rigid tubing Female/Female/ - - 6 mm (NFE 49100) Female (FFF) Operating pressure bar 2 8 2 8 2 8 Vacuum pad material - - - Weight g 80 13 25 Detection of the pressure decrease can be achieved by the use of manostats (see pages 38/39) Vacuum (mb) Vacuum (mb) Vacuum (mb) Suction flow Suction flow Suction flow Vacuum Vacuum (mb) (mb) Vacuum Flow (mb) Flow Flow Supply pressure (bar) Supply pressure (bar) Supply pressure (bar) Dimensions 81 535 301 81 545 001 Sub-base mounting 81 531 and 81 532 2 push-in connectors 4 mm Plug-in ferrule for push-in connector 4 mm 29 11 40 81 545 005 30,7 10,7 4,5 15,5 3 push-in connectors 6 mm 0,1 40 14,5 ATEX version products are available in the following catologues: Pneumatic products for explosive atmospheres or on our website www.crouzet.com Rfrence : Dsignation : Pneumatique 81540001 / 81541001 DESSINE PAR ST 000 637 P2 SODIPE Rfrence : Dsignation : Pneumatique 81540005 / 81541005 DESSINE PAR ST 000 638 P2 SODIPE 11 0,1 29 24 W W W.CROUZET-CONTROL.COM 42 PNEUMATICS PRODUCTS W W W.CROUZET-CONTROL.COM 43 PNEUMATICS PRODUCTS Sequencer modules General characteristics 100 % pneumatic Ideal for a simple pneumatic sequence Also available in ATEX version for use in poten- tially explosive atmospheres in accordance with 94/9/EC Directive Operating fluid flow graphs 81 550 001 81 550 201 81 550 401 81 550 601 - Compressed air or inert gas. sequencer with maintain Reset to zero - - Versions shift register - - with maintain Reset to zero Conditions of use of passage (mm) - Operating pressure 2 at 8 bars (except for special conditions). - Fluid: Filtered air to 50 microns - non lubricated. Symbol - Operating temperature from - 5 C to + 50 C (under + 5 C the P. supply pressure : dew point must be below 10 C for the application). 4 bars - For optimum performance, the elements should be inter-connected by air supply tubing with an internal diameter at 2.5 mm. Characteristics Mounting recommendations Operating pressure bar 2 8 2 8 2 8 2 8 - The elements should be mounted and piped in a clean atmosphere 2.7 2.7 Orifice diameter mm 2.7 2.7 in order to prevent any form of pollution entering the system. Flow at 6 bars Nl/min 150 150 150 150 - Minimum torque for element fixing screws: -5 +50 -5 +50 Operating temperature C -5 +50 -5 +50 5 cm/kg. 6 Mechanical life 5 x 10 at 6 bars l l l l - maximum torque for element fixing screws: l l Connection - Sub-base page 26 l l 10 cm/kg. Weight g 70 70 70 70 Characteristics common to all elements in the modular system Minimum pressure to be applied to port 1 - 4 - 7 - The characteristics have been obtained with a supply pressure at 6 to switch the valve P. supply pressure: bars. 6 bars - The flow in NI/min is the number of litres of air at normal atmosphe- ric pressure obtained with the output open to atmophere and the supply pressure at 4 bars - The consumption in NI/min is the number of litres of free air neces- sary for the unit to function. - kV = the flow coefficient of the equipment. Flow 7 - Mechanical life > 10 operations. (NL/mn) supply pressure (bar) Module with auto reset Sequencer modules Principle of operation Operation results from the combination of a sequential cycle. A (supplied without logic element. For choice of units see pages 46/47) system comprises individual modules which are joined together by means of a sub-base. Each module has a memory which delivers an Sequencer module with maintained reset Shif register with maintained reset output signal and receives an input signal. An indicator on each module allows the operator to monitor the pro- gress of the cycle and identity quickly and easily any fault which may occur. Brake This returns the memory spool to the reset condition only when the 1 - Input signal 1 - Input signal supply is lost 2 - Supply 2 - Supply 3 - Output signal 3 - Output signal Shift register 4 - Start signal 4 - Start signal The general principle is to advance the sequencer step by command 5 - In cycle signal 5 - In cycle signal impulses to the inputs of the even steps, alternating with the command 6 - End of cycle signal 6 - End of cycle signal impulses to the inputs of the odd steps. 7 - Reset to zero signal 7 - Reset to zero signal Used for example on a transfer machine to shift the informationbad componen collected at a test-test steps further along the machine Dimensions Mounting plan for sequencer Operation results from the combination of three functions (memory, to a reject station. AND and OR) which constitute each module. 2 holes M4 - minimum Function diagram The memory activates the output and gives priority to the reset signal. depth 7 mm The AND element ensures the transition to the next module but only if an input signal is present. The OR element ensures the resetting of all previously operated modules Function diagram Auto reset sequencer module ATEX version products are available in the following catologues: Pneumatic products for explosive atmospheres or on our website www.crouzet.com sequencer module with maintained reset Brake This maintains the memory spool in position only when the supply is lost.