LXPRF 400V

Type: LXPRF Phase Failure, Phase Sequence and Under Voltage Terminal *NEW* 17.5mm DIN rail housing Protection Microprocessor based to IP20 True R.M.S. monitoring Monitors own supply and detects an Under voltage condition on one or more phases Measures phase to phase voltages Detects incorrect phase sequence and phase loss Fixed Under voltage trip level Fixed Time delay 1 x SPDT relay output 8A Green LED indication for supply status Red LED indication for relay status Dims: to DIN 43880 W. 17.5mm FUNCTION DIAGRAM TTEECCHHNNIICCAALL SSPPEECCIIFFIICCAATTIIOONN FUNCTION DIAGRAM Supply/monitoring voltage Monitored 1 U* (L1, L2, L3): 77 - 143V, 161 - 300V, 280 520V AC 3~ Supply Phases reversed Frequency range: 48 63Hz * Please state L1 Supply variation: 30% Supply/monitoring L2 Overvoltage category: III (IEC 60664) 1 voltage when ordering L3 Rated impulse withstand voltage: 4kV (1.2/50S) IEC 60664 Power consumption (max.): 8VA Hyst. Monitoring mode: Under voltage Fixed Under trip Trip level (fixed) 2%: Under Supply voltage 77 143V: 77V Output 161 300V: 161V 280 520V: 280V Hysteresis: 2% of trip level (factory set) Td t t t Td Repeat accuracy: 0.5% at constant conditions Immunity from micro power cuts: <50mS Response time: 50mS Time delay (t): 100mS Installation work must be carried INSTALLATION AND SETTING INSTALLATION AND SETTING Note: actual delay (t) = delay + response time out by qualified personnel. Delay from Phase loss (tr): 150mS (worst case = tr x 2) BEFORE INSTALLATION, ISOLATE THE SUPPLY. Power on delay (Td): 1 sec. (worst case = Td x 2) Connect the unit as required. The Connection Diagram below shows a typical installation, Power on indication: Green LED whereby the supply to a load is being monitored by the Phase monitoring relay. If a fault should Relay status indication: Red LED occur (i.e. fuse blowing), the relay will de-energise and assuming control of the external Ambient temp: -20 to +60C Contactor, de-energise the Contactor as well. Relative humidity: +95% max. Applying power. Output (15, 16, 18): SPDT relay Output rating: AC1 250V 8A (2000VA) Apply power and the green Power supply and red Relay LEDs will illuminate, relay AC15 250V 5A (no), 3A (nc) energise and contacts 15 and 18 will close. Refer to the troubleshooting table if the unit fails to DC1 25V 8A (200W) operate correctly. Electrical life: 150,000 ops at rated load Dielectric voltage: 2kV AC (rms) IEC 60947-1 Note: Rated impulse withstand voltage: 4kV (1.2/50S) IEC 60664 If the supply voltage increases above the maximum supply/monitoring voltage range by approx. 10% Housing: Orange flame retardant UL94 V0 or more, the relay will de-energise immediately. Weight: 75g Mounting option: On to 35mm symmetric DIN rail to BS EN 60715 This device is not suitable for applications where there could be a percentage of re-generative voltage or direct surface mounting via 2 x M3.5 or 4BA screws present during a fault condition, i.e. fuse failure. During these conditions a monitor that includes an using the black clips provided on the rear of the unit. adjustable under voltage trip level is necessary which allows this type of fault to be detected. It is 2 Terminal conductor size 2 x 2.5mm solid or stranded therefore recommended that the LXPRT or LXPRT-4W phase monitors be considered. Approvals: Conforms to IEC. CE, and RoHS Compliant. Troubleshooting. EMC: Immunity: EN 61000-6-2 (EN 61000-4-3 15V/m 80MHz - 2.7GHz) The table below shows the status of the unit during a fault condition. Emissions: EN 61000-6-4 Supply fault Green LED Red LED Relay Phase missing On Off De-energised Phases reversed (no delay) Flashing Off De-energised Phase below 70% of Un (fixed under trip level 2 ) On Off De-energised CCOONNNNEECCTTIIOONN DDIIAAGGRRAAMM SSEETTTTIINNGG DDEETTAAIILLSS DDIIMMEENNSSIIOONNSS Local Fuse 89 (exc. clips) Board 1. Power supply status L1 Supply / 67.5 (Green) LED Monitored L2 45 To Load Voltage L3 2. Relay output (Red) LED L1 L2 Contactor L3 Insert screwdriver to release clips 15 R 16 18 Withdraw clips fully when 15 surface mounting 92 (+/- 1mm) 16 18 Phase Monitor all dimensions in mm. Broyce Control Ltd., Pool Street, Wolverhampton, West Midlands WV2 4HN. England LXPRF-2-A XXXXX Tel: +44 (0) 1902 773746 Fax: +44 (0) 1902 420639 Email: sales broycecontrol.com Web: www.broycecontrol.com The Information provided in this literature is believed to be accurate (subject to change without prior notice) however, use of such information shall be entirely at the users own risk. 29 49.5 66.5X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Broyce Control manufacturer: Other Similar products are found below : LART 12-230V AC/DC LXCVR 230V LBVR/A 12-24VDC LMCCR-10A LESW 12-230V AC/DC