ABCU-5740ARZ Broadcom

ABCU-57xxxxZ Family 10/100/1000BASE-T 1.25 GBd Small Form Pluggable Low Voltage (3.3 V) Electrical Transceiver over Category 5 Cable Data Sheet Description Features RoHS-6 Compliant (see Table 1) The ABCU-57xxxxZ family of electrical transceivers from Avago Technologies off er full-duplex throughput of 1000 Designed for Industry-Standard, Small Form Factor Mbps by transporting data over shielded and unshielded Pluggable (SFP) Ports twisted pair category 5 cable with 5-level PAM (Pulse Compliance with IEEE 802.3:2005 Amplitude Modulation) signals. Custom RJ-45 connector with integrated magnetics The Avago Technologies 1000BASE-T module takes sig- Link lengths at 1.25 Gbd: up to 100 m per IEEE802.3 nals from both the twisted pair category 5 cable and the Low power, high performance 1.25 Gbd SerDes inte- SerDes interface. Pin count overhead between the MAC grated in module and the PHY is minimized, and Gigabit Ethernet opera- Single +3.3 V power supply operation tion is achieved with maximum space savings. Auto-negotiation per IEEE 802.3:2005 Clause 28 Product Ordering Information (Twisted Pair) and Clause 37 (1000BASE-X) Compatible to both shielded and unshielded twisted ABCU-5730RZ -5~70 RX LOS enabled pair category 5 cable ABCU-5740RZ -5~70 RX LOS disabled Available in Commercial Temperature (-5~70 C) and ABCU-5730GZ -5~70 RX LOS enabled & Isolated Industrial Temperature (-40~85 C) ground 10/100/1000BASE-T operation available with SGMII ABCU-5730ARZ -40~85 RX LOS enabled host systems. ABCU-5740ARZ -40~85 RX LOS disabled ABCU- 5740AGZ -40~85 RX LOS disabled Applications & Isolated ground Switch to switch interface ABCU-5731ARZ -40~85 SGMII RX LOS enabled Switched backplane applications ABCU-5741ARZ -40~85 SGMII RX LOS disabled File server interface ABCU-5741AGZ -40~85 SGMII RX LOS disabled & Module Diagrams Isolated ground ABCU-5731RZ -5~70 SGMII RX LOS enabled Figure 1 illustrates the major functional components ABCU-5741RZ -5~70 SGMII RX LOS disabled of the ABCU-57xxxxZ family of transceivers. The 20-pin connection diagram of module printed circuit board of the module is shown in Figure 2. Figure 3 depicts the pin Related Products assignment of the MDI (RJ45 jack). AFBR-5710Z Family of 850nm +3.3V SFP optical Figure 6 depicts the external confi guration and dimen- transceivers for Gigabit Ethernet sions of the module. AFCT-5710Z Family of 1310nm +3.3V SFP optical transceivers for Gigabit EthernetInstallation Serial Identifi cation (EEPROM) The ABCU-57xxxxZ family can be installed in or removed The ABCU-57xxxxZ family complies with an industry stan- from any MultiSource Agreement (MSA) compliant Small dard MultiSource Agreement that defi nes the serial identi- Form Pluggable port whether the host equipment is fi cation protocol. This protocol uses the 2-wire serial CMOS operating or not. The module is simply inserted, small EEPROM protocol of the ATMEL AT24C01A or equivalent. end fi rst, under fi nger-pressure. Controlled hot-plugging The contents of the ABCU-57xxxxZ family serial ID memory is ensured by design and by 3-stage pin sequencing at are defi ned in Table 10 as specifi ed in the SFP MSA. the electrical interface to the host board. The module Controller and Data I/O housing makes initial contact with the host board EMI shield, mitigating potential damage due to ElectroStatic Data I/Os are designed to accept industry standard dif- Discharge (ESD). The module pins sequentially contact ferential signals. In order to reduce the number of passive the (1) Ground, (2) Power, and (3) Signal pins of the host components required on the customers board, Avago board surface mount connector. This printed circuit board Technologies has included the functionality of the trans- card-edge connector is depicted in Figure 2. mitter bias resistors and coupling capacitors within the module. The transceiver is compatible with an ac-coupled TX DISABLE confi guration and is internally terminated. Figure 1 depicts TX DATA the functional diagram of the ABCU-57xxxxZ family of RX DATA transceivers. 100-ohm resistor shown at RX LOS in Figure 1 refers to ABCU-573xxxZ confi guration. RJ45 SerDes/ RX LOS 100 Magnetics Adapter DSP Caution should be taken into account for the proper inter- MOD DEF2 connection between the supporting Physical Layer integrat- MOD DEF1 ed circuits and the ABCU-57xxxxZ family of transceivers. MOD DEF0 100 Figure 4 illustrates the recommended interface circuit. Several control data signals and timing diagrams are imple- mented in the module and are depicted in Figure 6. EEPROM Figure 1. Transceiver Functional Diagram PIN 8 PIN 1 20 V T 1 V T EE EE 19 TD- 2 TX FAULT 18 TD+ 3 TX DISABLE 17 V T 4 MOD-DEF(2) EE 16 V T 5 MOD-DEF(1) CC 15 V R 6 MOD-DEF(0) CC 14 V R 7 Rate Select EE 13 RD+ 8 LOS 12 RD- 9 V R EE 11 V R 10 V R EE EE Figure 3. MDI ( RJ 45 Jack) Pin Assignment Bottom of Board Top of Board (as viewed thru top of board) Note: LOS is only applicable for ABCU-573xxxZ models Figure 2. 20-pin Connection Diagram of Module Printed Circuit Board 2