2C24-P125

SINGLE OUTPUT HIGH VOLTAGE MODULES 10 HIGH POWER C SERIES High Voltage Cap-Charging Supply This High Power line of high-voltage regulated DC to DC converters is an extension of the C Series, directly addressing the high power density needs of >30 watt applications. High Power C units provide up to 60/125/250 watts. This high power density is especially suited to high-energy systems with large capacitances, fast repetition rates, or high continuous-DC-power requirements. See Application Note 10 for more charging information. Typical applications for the High Power C Series include the following: laser, cap-charging, pulsed power, pulse generator, and test equipment. High efficiency High power to voltage density 7 models from 0 to 125 Volts through 0 to 6kV Very low profile 60, 125, or 250 watts of output power Output current & voltage monitors Maximum Iout capability down to 0 Volts >200,000 hour MTBF 65C Maximum Iout during charge/rise time Fixed-frequency, low-stored-energy design Output short-circuit protection Very fast rise with very low overshoot UL/cUL Recognized Component CE Mark (LVD & RoHS) PARAMETER CONDITIONS UNITS INPUT ALL TYPES Voltage Range Full Power + 23 to 30 VDC Voltage Range Derated Power Range + 11 to 32 VDC Current Standby / Disable < 40 mA Current Max Load, Max Eout 60W: 3, 125W: 6 250W: 12 A Current No Load, Max Eout 1/8C to 1C: < 300, 2C to 6C: < 500 mA AC Ripple Current Nominal Input, Full Load < 50 mA p-p OUTPUT 1/8C 1/4C 1/2C 1C 2C 4C 6C Voltage Range Nominal Input 0 to 125 0 to 250 0 to 500 0 to 1,000 0 to 2,000 0 to 4,000 0 to 6,000 VDC Power Nominal Input, Max Eout 60 125 250 60 125 250 60 125 250 60 125 250 60 125 250 60 125 250 60 125 250 Watts Current Iout, Entire Output Voltage Range 480 1000 2000 240 500 1000 120 250 500 60 125 250 30 62 125 15 31 62 10 21 42 mA Current Scale Factor Full Load 400 833 1667 200 417 833 109 208 417 50 114 227 26 52 104 11.5 26 52 6.2 17.7 35 mA/V Voltage Monitor Scaling - 100:1 2% into 10M Ripple Full Load, Max Eout, Cload 0.5uF < 1.0 %V p-p Overshoot C Load, 0 Eout to Full Eout < 1 %V pk Rise Time Max Iout, Various C Loads & Eout Figure A - Storage Capacitance Internal 0.90 0.90 1.80 0.90 0.90 1.80 0.43 0.43 0.85 0.019 0.019 0.038 0.019 0.019 0.038 0.013 0.013 0.026 0.013 0.013 0.026 uF Line Regulation Nom. Input, Max Eout, Full Power < 0.01% VDC Static Load Regulation No Load to Full Load, Max Eout < 0.01% VDC Stability 30 Min. warmup, per 8 hr/ per day < 0.01% / < 0.02% VDC PROGRAMMING & CONTROLS ALL TYPES Input Impedance Nominal Input + Output Models 1.1M to GND, - Output Models 1.1M to +5 Vref M Adjust Resistance Typical Potentiometer Values 10K to 100K (Pot across Vref. & Signal GND, Wiper to Adjust) Adjust Logic 0 to +5 for +Out, +5 to 0 for - Out +4.64 VDC for +Output or +0.36 for -Output = Nominal Eout - Output Voltage & Impedance T=+25C + 5.00VDC 2%, Zout = 464 1% - Enable/Disable (ON/OFF) 0 to +0.5 Disable, +2.4 to 32 Enable (Default = Enable) VDC ENVIRONMENTAL ALL TYPES Operating Full Load, Max Eout, Case Temp. -40 to +65 C Coefficient Over the Specified Temperature PPM/C 50 ( 25 Optional) Thermal Shock Mil-Std 810, Method 503-4, Proc. II -40 to +65 C Storage Non-Operating, Case Temp. -55 to +105 C Humidity All Conditions, Standard Package 0 to 95% non-condensing - Altitude Standard Package, All Conditions Sea Level through 70,000 ft Shock Mil-Std-810, Method 516.5, Proc. IV 20 Gs Vibration Mil-Std-810, Method 514.5, Fig.514.5C-3 10 Gs Specifications are subject to change without notice. C = uF C = uF C = uF V = Volts V = kV V = kV C = uF I C x V C x E I = C x V x F F= I = mA T= I = mA I = mA E = kV J= C x V I 2 T = mS F = Hz F = Hz J = Ws Figure A - Rise Time Formulas NOTE: Capacitance must include HVPS internal Capacitance. Higher Service, Higher Performance, Higher Reliability Making High Voltage Easier 2011, UltraVolt Inc. All rights reserved. ULTRAVOLTRev. Y 2/14 SINGLE OUTPUT HIGH VOLTAGE MODULES 11 HIGH POWER C SERIES High Voltage Cap-Charging Supply 60W/125W CONSTRUCTION Epoxy-lfi led Aluminum Box Chem lfi m per MIL-A-8625 Type II (Anodizing) SIZE Volume: 60W/125W: 19.35in (317cc) 250W: 38.7in (634cc) Weight: 60W/125W: 1.4 lbs (.64kg) 250W: 2.6 lbs (1.18kg) TOLERANCE Overall 0.025 (0.64) Pin to Pin 0.015 (0.38) Hole to Hole location 0.025 (0.64) 250W Downloadable drawings (complete with mounting & pin information) and 3D models are available online. CONNECTIONS ORDERING INFORMATION HIGH POWER PIN CONNECTIONS 0 to 125 VDC Output 1/8C PIN FUNCTION (250 WATT UNITS) 1 & 8 Input Power Ground Return 0 to 250 VDC Output 1/4C PIN FUNCTION 0 to 500 VDC Output 1/2C 2 & 9 Positive Power Input 2, 9, & 10 N/C 3 Iout Monitor Type 0 to 1,000 VDC Output 1C 19 & 20 Positive Power Input 0 to 2,000 VDC Output 2C 4 Enable/Disable 21 & 22 Input Power Ground Return 0 to 4,000 VDC Output 4C 5 Signal Ground Return 0 to 6,000 VDC Output 6C 6 Remote Adjust Input Input 24VDC Nominal 24 7 +5VDC Reference Output Positive Output -P 10, 11, 12, & 13 N/C Polarity Negative Output -N 14 Eout Monitor 60 Watts Output 60 15 & 16 HV Ground Return IEC-60950-1 Power 125 Watts Output 125 17 & 18 HV Output 250 Watts Output 250 Non-RoHS compliant units are available. Please contact the Heat Sink .400 High (sized to fit case) -H factory for more information. PCB Support (5 or 7) 0.187 standoffs on top cover -Z11 All grounds joined internally. Power-supply mounting points isolated from internal grounds 5V Control and Monitors -I5 Enhanced by >100k, .01uF / 50V (Max). Interface 10V Control and Monitors -I10 Example: Options 25PPM Temperature Coefficient -25PPM 1/2C24-P125 Voltage Note: For more information on the enhanced interface options, Type download the I5/I10 Option datasheet. Model Power Input Polarity Popular accessories ordered with this product include CONN- KIT-HP250, CONN-KIT-HP and the BR-8 mounting bracket kit. 1800 Ocean Avenue, Ronkonkoma, NY 11779 Making High Voltage Easier Phone: 1-631-471-4444 Fax: 1-631-471-4696 www.ultravolt.com ULTRAVOLT