3M MetPak HSHM Press-Fit Header 2 mm Type B19, 95 Signal Contacts, 5 Rows, Straight HSHM Series Up to 5 Gb/s data rates Low crosstalk at high frequencies 50/100 (single-ended /differential) impedance Modular/scalable format IEC 61076-4-101 63 mated lines per linear inch End-to-end stackable with 5 row 3M MetPak CP2, HM and HSHM sockets Mates with 3M MetPak HSHM sockets See the Regulatory Information Appendix (RIA) in the RoHS compliance section of www.3mconnector.com for compliance information Date Modi ed: November 9, 2010 TS-2220-B Sheet 1 of 3 Physical Insulation Material: High Temperature Thermoplastic (LCP) Flammability: UL 94V-0 Contact Material: Copper Alloy Plating: See Ordering Information Performance Mechanical: Normal Force (Nominal): 0.57 N 58 g Signal, 0.74 N 75 g Shield Engagement Force (Nominal): 0.32 N 33 g Signal, 0.22 N 22 g Shield Separation Force (Nominal): 0.20 N 20 g Signal, 0.20 N 20 g Shield Wipe (Nominal, Shortest Contact): 2.67 mm 0.105 in Signal, 1.57 mm 0.062 in Shield Mate/Unmate Cycles: 250 Application: This module is not suitable for stand-alone use. (Refer to IEC-61076-4-101) Electrical: Data Rate: 5 Gb/s Characteristic Impedance: 50 Single-ended, 100 Differential Current Rating (Fully Loaded): 1 A 70C Signal 4 Insulation Resistance: 10 M 100 V DC Withstanding Voltage: 750 V rms Environmental Temperature Rating: -55 C to 125 C UL File No.: E68080 MetPak is a trademark of 3M Company. 3M is a trademark of 3M Company. For technical, sales or ordering information call Electronic Solutions Division 800-225-5373 Interconnect Solutions 3M MetPak HSHM Press-Fit Header 2 mm Type B19, 95 Signal Contacts, 5 Rows, Straight HSHM Series mm (Inch) Tolerance Unless Noted 0 0.0 0.00 mm 3 0.3 0.13 Dimensions for Reference Only Standard Con guration DIM A = 5.3 mm for rows A through E For non-standard con gurations, contact sales representative Ordering Information (rows F and Z not loaded) HSHM-H095BX - 5CPX- XXXXX Plating m : High Speed Option: TG30 = 0.76 30 Min. Au Contact Area 4 =Coaxial, column differential and stripline 2.54 100 Min. SnPb Terminal Area (RIA C2 & E2 apply) (75 ) applications 1.27 50 Min. Ni All over Standard Option 5 =Row differential applications TG30L = 0.76 30 Min. Au Contact Area, Lubricated 2.54 100 Min. SnPb Terminal Area (RIA C2 & E2 apply) 1.27 50 Min. Ni All over Typically higher make order quantities as compared to TG30. TG50 = 1.27 50 Min. Au Contact Area, Lubricated 2.54 100 Min. SnPb Terminal Area (RIA C2 & E2 apply) Tail Length: 1.27 50 Min. Ni All over 1 =4.4 mm pin and 3.5 mm shield Non-Standard Option (Available with longer lead times and 2 =2 mm pin and 2 mm shield higher make order quantities, MOQ) TS-2220-B Sheet 2 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call Electronic Solutions Division 800-225-5373 Interconnect Solutions