LB02VA002 NKK Switches

Standard Size Indicator with Legend LB Indicator LB02VA002 PANEL CUTOUT Snap-in Mount Dimensions in mm/inch (22.0) Dia .866 (1.2) x (2.0) Typ .047 x .079 (0.5) Typ (+) L .020 (15.8) Sq OFF .622 (11.5) .453 (2.54) Typ .100 L (-) Part No. (1.5) R This Side .059 (19.0) Dia (1.8) (2.8) Panel Thickness .748 .071 .110 (23.7) Dia (3.2) (21.5) (7.5) (21.7) Dia .039 ~ .157 .933 .126 .846 .295 .854 (1.0mm ~ 4.0mm) ROUND CAP LEGEND SPECIFICATIONS BASE INDICATOR Legend OFF AT4164JB (19.0) Dia Type Style Helvetica Bold Round Cap (4.5) .748 .177 Type Size 10 Point Part Number Clear Lens Legend Color Black White Insert LB02KW01 Laser Etch on (5.5) Print Method Material: Polycarbonate .217 Inside of Lens Finish: Glossy Legend shown is illustrative only. Actual art may vary. ELECTRICAL SPECIFICATIONS FOR LED Bright LED LED is 5-volt 4-element with resistor The electrical specifications shown are determined at a AT627C05 basic temperature of 25C. If the source voltage exceeds Color Red the rated voltage, a ballast resistor is required. The follow- Maximum Forward Current I ing diagram and formula will assist in calculating the value FM of the ballast resistor. Typical Forward Current I 52mA F E V R I F + F R = Forward Voltage V 5V F I Anode F Maximum Reverse Voltage V 4V Where: R = Resistor Value (Ohms) RM (+) (-) E V F E = Source Voltage (V) Current Reduction Rate Above 25C I 0.50mA/C V = Forward Voltage (V) F F Cathode I = Forward Current (A) F T-1 Bi-pin Ambient Temperature Range 25C ~ +50C Base Indicator Specifications Materials & Finishes Housing: Glass fiber reinforced polyamide (UL94V-0) Snap-in Frame: Stainless steel Base: Liquid crystal polymer (UL94V-0) Lamp Terminals: Brass with silver plating Environmental Data Operating Temperature Range: 25C through +50C (13F through +122F) Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0C (32F) Humidity: 90 ~ 95% humidity for 96 hours @ 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 2 Shock: 50G (490m/s ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) RoHS Compliant: Installation Cap Installation Force: 3.92N maximum downward force on cap Quick Connect Force: 52.95N maximum downward force on connector Soldering Time & Temperature: Manual Soldering: 390C for 4 seconds, 2 cycles Standards & Certifications Flammability Standards: UL94V-0 housing & base www.nkkswitches.com 07/02/18X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Industrial Panel Mount Indicators / Switch Indicators category: Click to view products by NKK Switches manufacturer: Other Similar products are found below : LW1A-P1-W LW1B-A0L 01-152.025 D38999/20FJ29PB L/C 704-6020 704-6026 73.362.4028.0 EUS-704.000.7 750-1520 9001OA120 99-450.837 99-455.837 99-486.837 99-901.9 99-902.9 99-908.0 99-909.4 99-909.5 A0244J1 A3DT-500Y AL6M-P7P-A AOLQW-2B0600 AP1M255-A APD106LN-A APD106LN-G APN1126-G APS122DN-W ATN2100 AYLW4L-A 18-237.035 C0180AANAH HW1A-L1- GD HW1A-P2-GL HW1F-3G HW1R-2DF20-R HW1X-BM411-R HW2A-L1-GL HW2A-P1-GD HW4S-31L HWAZ1N-OB PA2200/1 PA2SHIELD 21-931.2 96-923.5 1625006 99-451.837 99-480.837 99-481.837 99-908.9 99-909.2