MT29F1G08ABBFAH4-ITE:F Micron

Micron Confidential and Proprietary 1Gb: x8 NAND Flash Memory Features NAND Flash Memory MT29F1G08ABAFAWP-ITE:F, MT29F1G08ABAFAH4-ITE:F, MT29F1G08ABBFAH4-ITE:F 2 ECC: 8-bit internal ECC is enabled by default. It Features can not be disabled 1 Open NAND Flash Interface (ONFI) 1.0-compliant Blocks 7-0 are valid when shipped from factory with Single-level cell (SLC) technology ECC Organization RESET (FFh) required as first command after pow- Page size x8: 2176 bytes (2048 + 128 bytes) er-on Block size: 64 pages (128K + 8K bytes) Alternate method of device initialization after pow- Plane size: 1 planes x 1024 blocks per plane er-up (contact factory) Device size: 1Gb: 1024 blocks Internal data move operations supported within the Asynchronous I/O performance plane from which data is read t t RC/ WC: 20ns/20ns (3.3V), 30ns/30ns (1.8V) Quality and reliability Array performance Endurance: 100,000 PROGRAM/ERASE cycles Read page: 80s Data retention: JESD47G-compliant see qualifi- Program page: 220s (TYP 3.3V/1.8V) cation report Erase block: 2ms (TYP) Additional: Uncycled data retention: 10 years Command set: ONFI NAND Flash Protocol 24/7 85C Advanced command set Operating voltage range Program page cache mode V : 2.73.6V CC Read page cache mode V : 1.71.95V CC Permanent block locking (blocks 47:0) Operating temperature: One-time programmable (OTP) mode Industrial (IT): 40C to +85C Block lock (1.8V only) Package 3 Programmable drive strength 48-pin TSOP type 1, CPL Read unique ID 63-ball VFBGA Internal data move Operation status byte provides software method for 1. The ONFI 1.0 specification is available at Notes: detecting www.onfi.org. Operation completion 2. Refer to the Part Numbering Information to Pass/Fail condition check the default status of the ECC. If ECC is enabled by default, it can not be disabled. Write-protect status 3. CPL = Center parting line. Ready/Busy (R/B ) signal provides a hardware method of detecting operation completion WP signal: Write protect entire device CCMTD-1725822587-10323 Micron Technology, Inc. reserves the right to change products or specifications without notice. 1 m78a 1gb ecc on embedded nand.pdf Rev. E 6/19 EN 2016 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice.Micron Confidential and Proprietary 1Gb: x8 NAND Flash Memory Features Part Numbering Information Micron NAND Flash devices are available in different configurations and densities. Verify valid part numbers by using Microns part catalog search at www.micron.com. To compare features and specifications by device type, visit www.micron.com/products. Contact the factory for devices not found. Figure 1: Marketing Part Number Chart MT 29F 4G 08 A B A F A H4 - AAT ES :F Design Revision (shrink) Micron Technology D = Design Revision D Product Family E = Design Revision E 29F = NAND Flash memory F = Design Revision F G = Design Revision G Density 1G = 1Gb Production Status 2G = 2Gb Blank = Production 4G = 4Gb ES = Engineering sample 8G = 8Gb MS = Mechanical sample QS = Qualification sample 16G = 16Gb Device Width Special Options 08 = 8-bit E = Internal ECC enabled by default (Parallel) 16 = 16-bit Blank = Internal ECC disabled by default (Parallel) Level Operating Temperature Range A = SLC Blank = Commercial (0C to +70C) IT = Industrial (40C to +85C) Classification AIT = Automotive Industrial (40C to +85C) Mark Die nCE RnB I/O Channel AAT = Automotive (40C to +105C) B 1 1 1 1 Speed Grade D 2 1 1 1 12 = 166 MT/s (synchronous mode) J 4 2 2 1 Blank = Asynchronous mode Operating Voltage Range Package Code A = 3.3V (2.73.6V) SF = 16-pin SO (10.3mm x 10.3mm x 2.65mm) B = 1.8V (1.71.95V) WB = 8-pin U-PDFN (8mm x 6mm x 0.65mm) C = V : 3.3V (2.73.6V) V : 1.8V (1.71.95V) CC CCQ W9 = 8-pin W-PDFN (8mm x 6mm) 12 = 24-ball TBGA (6mm x 8mm x 1.2mm) Generation Feature Set WP = 48-pin TSOP Type 1 D = Feature set D HC = 63-ball VFBGA (10.5mm x 13mm x 1.0mm) E = Feature set E H4 = 63-ball VFBGA (9mm x 11mm x1.0mm) F = Feature set F G = Feature set G Interface A = Asynchronous only B = Sync/Async CCMTD-1725822587-10323 Micron Technology, Inc. reserves the right to change products or specifications without notice. 2 m78a 1gb ecc on embedded nand.pdf Rev. E 6/19 EN 2016 Micron Technology, Inc. All rights reserved.