Ships to you between Mon. 10 Jun to Wed. 12 Jun
WP934SA/IYGD5V T-1 (3mm) Tri-Level Circuit Board Indicator DESCRIPTIONS PACKAGE DIMENSIONS The High Efficiency Red source color devices are LED1 : Red LED2 : Yellow made with Gallium Arsenide Phosphide on Gallium LED3 : Green Phosphide Orange Light Emitting Diode The Yellow source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Yellow Light Emitting Diode The Green source color devices are made with Gallium Phosphide Green Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs All devices, equipments and machineries must be electrically grounded FEATURES Pre-trimmed leads for pc mounting Black case enhances contrast ratio High reliability life measured in years Housing UL rating: 94V-0 Housing material: Type 66 nylon 5V internal resistor RoHS compliant APPLICATIONS Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01 ) unless otherwise noted. Status indicator 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change Illuminator without prior notice. Signage applications Decorative and entertainment lighting Commercial and residential architectural lighting ATTENTION Observe precautions for handling electrostatic discharge sensitive devices SELECTION GUIDE 2 1 Iv (mcd) V = 5V Viewing Angle Emitting Color Part Number Lens Type (Material) Min. Typ. 21/2 12 25 High Efficiency Red Red Diffused 50 (GaAsP/GaP) *6 *14 7 15 WP934SA/IYGD5V Yellow Diffused 50 Yellow (GaAsP/GaP) *7 *15 12 25 Green (GaP) Green Diffused 50 *12 *25 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Page 1 / 5 2019 Kingbright. All Rights Reserved. Spec No: DSAH1032 / 1102015746 Rev No: V.5A Date: 11/22/2019 WP934SA/IYGD5V ELECTRICAL / OPTICAL CHARACTERISTICS at T =25C A Value Parameter Symbol Emitting Color Unit Typ. Max. High Efficiency Red 627 Wavelength at Peak Emission V = 5V Yellow 590 - nm F peak Green 565 High Efficiency Red 617 1 Dominant Wavelength V = 5V Yellow 588 - nm F dom Green 568 High Efficiency Red 45 Spectral Bandwidth at 50% REL MAX Yellow 35 - nm V = 5V F Green 30 High Efficiency Red 13 17.5 Forward Current V = 5V I Yellow 13 17.5 mA F F Green 11.5 17.5 High Efficiency Red 10 Reverse Current (V = 5V) I Yellow - 10 A R R Green 10 Notes: 1. The dominant wavelength ( d) above is the setup value of the sorting machine. (Tolerance d : 1nm. ) 2. Wavelength value is traceable to CIE127-2007 standards. 3. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at T =25C A Value Parameter Symbol Unit High Efficiency Red Yellow Green Power Dissipation P 85 85 85 mW D Reverse Voltage V 5 V R Junction Temperature T 125 110 110 C j Operating Temperature T -40 to +70 C op Storage Temperature T -40 to +85 C stg Forward Voltage V 6 6 6 V F Electrostatic Discharge Threshold (HBM) 3000 3000 3000 V - 1 Lead Solder Temperature 260C For 3 Seconds 2 Lead Solder Temperature 260C For 5 Seconds Notes: 1. 2mm below package base. 2. 5mm below package base. 3. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity Ref JEDEC/JESD625-A and JEDEC/J-STD-033. Page 2 / 5 2019 Kingbright. All Rights Reserved. Spec No: DSAH1032 / 1102015746 Rev No: V.5A Date: 11/22/2019
