10GENW3E

SNAP-IN MOUNTING HIGH PERFOR- VV DD EE OROR SERIES MANCE IEC CONNECTOR FILTERS INTRODUCTIONS SPECIFICATIONS 1. Snap-in mounting type to reduce labor cost. 1. Maximum leakage current each Compact and reliable at low cost. line-to-ground 115VAC 60Hz: 0.2mA 2. Bleeder resistor can be added with suffix- 250VAC 50Hz: 0.4mA on part numbers, except G3H,G3V,W3V,G3J,W3J,types. 2. Hipot rating (one minute) 3. Optional side snap-in mounting clip type with suffix (H) on part line-to-ground: 2250VDC numbers. line-to-line: 1450VDC 4. All part numbers are UL recognized, CSA certified and VDE 3. Operating frequency: 50/60Hz approved. 4. Rated voltage: 115/250VAC 5. With optional Y-Cap from 100pF to 3300pF. COMPONENTS INSERTION LOSS (TYPICAL) PART NO. Cx (uF) L (mH) Cy (pF) R ( ) DIFF. MODE COMMON MODE 03GENG3E 01GENG3E/W3E/-R 6.5 DIFF. MODE 03GENG3E/W3E/-R 2.5 COMMON MODE 06GENG3E 03GENG3U/-R 2.5 80 dB 03GENW3ES/-R 2.5 03GENG3Q/W3Q/-R 4 06GENG3E/W3E/-R 0.8 60 dB 06GENG3U/-R 0.8 06GENG3Q/W3Q/-R 1.5 0.1 2200 1M 06GENW3ES/-R 0.8 10GENG3E/W3E/-R 0.2 40 dB 10GENG3C/W3C/-R 0.4 10GENG3Q/W3Q/-R 0.3 *** 10GENG3U/-R 0.3 20 dB 10GENW3ES/-R 0.2 15GENG3E/W3E/-R 0.2 ** 20GENG3E/W3E/-R 0.3 0 dB *** 1M 10K 100K 10M UL, CSA approved to 13A 115/250V UL, CSA approved to 4A 115/250V * VDE approved to 10A/250V UL, CSA approved to 8A 115/250V ** VDE approved to 16A/250V VDE approved to 8A/250V *** COMMON MODE DIFF.MODE 20GENG3E 80 dB MINIMUM INSERTION LOSS IN dB COMMON MODE (L-G) IN 50 OHM SYSTEM CURRENT FREQUENCY-MHz 60 dB RATING .15 .50 1.0 5.0 10 30 1A 283538384040 3A 20 25 30 38 40 40 40 dB 6A 12 18 24 35 40 40 6A (G3Q) 15 20 24 35 40 55 10A 4 10 13 28 35 40 20 dB 10A (G3C) 10 15 15 25 30 35 10A (G3Q) 10 12 15 30 32 45 15A 4 10 13 28 35 40 0 dB 20A 8 10 15 25 30 35 1M 10K 100K 10M ELECTRICAL SCHEMATIC L L Cy L L R Cx I O N A Cy E D N N G G R: 1M /-R ONLY 2-7 IEC INLET FILTERSPANEL Suggested thickness of mounting panel is from PCB 0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout ASSEMBLY FROM FRONT 1.22 0.02 MECHANICAL CONSTRUCTION 31.0 0.5 L N G R0.08MAX. +0.012 R2.0MAX. 1.12 -0 +0.3 0.0315~0.06 28.45 -0 0.8~1.6 SUGGESTED MOUNTING CUTOUT NG3E, NG3C, NG3Q (Optional wire type) 1.12 MAX. 28.4 MAX. GENG3E 1.22 0.02 31.0 0.5 L N G R0.08MAX(2X) R2.0MAX 1.16 0.004 0.0315~0.063 29.5 0.1 0.8~1.6 SUGGESTED MOUNTING CUTOUT 1.12 MAX. NG3E(H), NG3C(H), NG3Q(H) (Optional wire type) 28.4 MAX. GENG3E(H) 1.22 0.02 31.0 0.5 L N G R0.08MAX. +0.012 R2.0MAX. 1.12 -0 +0.3 0.0315~0.06 - 28.45 0 0.8~1.6 SUGGESTED MOUNTING CUTOUT 1.10 0.02 NG3U (With Compact Size) 28.0 0.5 NG3U L N G 1.22 0.2 31.0 0.5 1.12 MAX. R0.08MAX. +0.012 28.4 MAX. R2.0MAX. 1.12 -0 +0.3 0.0315~0.06 - 28.45 0 0.8~1.6 SUGGESTED MOUNTING CUTOUT NW3ES NW3ES 2.60MAX. 1.18 66.0MAX. 30.0 0.248X0.031 6.3X0.8 0.138 3.5 3.19MAX. 81.0MAX. R0.118MAX. +0.02 R4.0MAX. 1.417-0 +0.5 36.0-0 SUGGESTED MOUNTING CUTOUT 20GENG3E (Optional wire type) (MOUNTING FROM REVERSE) INCH UNIT: mm WIRE LENGTH : 4.0 MIN. 2-8 IEC INLET FILTERS 0.945 0.02 0.945 0.02 0.945 0.02 24.0 0.5 24.0 0.5 24.0 0.5 1.36MAX. 1.04MAX. 34.5MAX. BROWN 26.5MAX. G/Y BLUE +0.04 1.575 MAX. 0.142 -0.02 0.945 0.02 1.66MAX. 1.66MAX. +1.0 40.0 MAX. 1.50 0.02 3.6 -0.5 24.0 0.5 42.16MAX. 42.16MAX. 38.0 0.5 +0.04 +0.04 +0.04 2.1MAX. 0.142 -0.02 2.1MAX. 0.142 -0.02 - 1.94 0.04 0.11 0.02 53.4MAX. +1.0 53.4MAX. +1.0 49.4 1.0 +1.0 - - 3.6 0.5 3.6 0.5 2.8- 0.5 0.84MAX. 21.3MAX. +0.02 1.496MAX. 1.043-0 38.0MAX. +0.5 26.5-0 0.862 0.004 21.9 0.1 0.862 0.004 0.862 0.004 21.9 0.1 0.85 0.004 21.9 0.1 21.5 0.1 0.8 0.02 20.4 0.5 0.84MAX. 0.84MAX. 21.4MAX. 21.4MAX.