515-1070F

3 x 5mm Rectangular Optopipe Optical Light Pipe, 2 Array (RJ45 Jack) 515-1070 19.05 .750 FRONT Recommended PANEL 13.98 31.24 .550 1.23 5.08 DIFFUSED 29.0 2.54 MicroLED SMT LEDs .200 FRONT 1.142 .100 2 PLCS SURFACE for use with 515-1070 3.05 .120 20.57 .81 3.56 1.91 .140 .075 PART NO. COLOR PAGE 3.93 597-3001-1xx Red 1-19 .155 C.L. LEDS 3.66 7.62 .15 597-3111-1xx AlGaAs Red 1-19 .144 27.94 .300 .006 1.100 27.43 1.57 1.080 597-3111-5xx AlGaAs Red 1-30 35.26 .062 1.388 C.L. MOUNTING 597-3211-1xx Orange 1-19 PIN 1 .71 1.50 .028 .059 597-3211-5xx Orange 1-30 .99 2.01 .99 .039 .079 1.57 597-3301-1xx Green 1-19 .039 .062 DIRECTION 597-3301-5xx Green 1-30 OF LIGHT NOTE: designed for 1.35 post-reflow 2X 2.87 .05 .053 597-3401-1xx Yellow 1-19 6.99 .113 .002 13.98 PC board insertion275 .550 597-3401-5xx Yellow 1-30 27.94 .05 1.100 .002 597-7701-1xx Red/Green 1-20 Dimensions in mm inches RECOMMENDED SOLDER PAD/HOLES LAYOUT FOR BI-COLOR LEDS 597-7701-5xx Red/Green 1-31 597-7721-1xx Yellow/Green 1-20 Features 597-7721-5xx Yellow/Green 1-31 Complements Dialights 515-1022 Four Array Optopipe 597-7731-1xx Red/Yellow 1-20 Light Pipe Allows indicators to be positioned above corresponding LED Data RJ45 jack or D-Subminiature For absolute maximum ratings and other electri- High transmissivity polycarbonate material cal and optical data on the recommended LEDs, UL94V-0 compliance refer to LED data sheets. ESD protection (circuit isolation from front panel) Wide viewing angle Operating/Storage Temperature Arrays reduce insertion costs 30C to +100C Secures to PCB by press-fit Dialight Optopipe Light Pipe Description This light pipes two 3 x 5mm rectangular light emitting surfaces appear bright and are optically well isolated. The light pipe is reliably held in place by 2 press-fit pins located at either end of the light pipe array. This Optopipe functions as a through-the-case indicator by conducting the light over the top of connectors or switches. A textured finish on the 2 light emitting surfaces maximizes the viewing angle. The recommended light sources are Dialight s 597 Series PLCC-2 or PLCC-4 Type SMT LEDs. The LEDs are mounted in a straight line on an 0.550 pitch. The light pipe material is water clear transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index. Dialight can provide custom Optopipe solutions for your applications. Dialight Corporation 1501 Route 34 South Farmingdale, NJ 07727 TEL: (732) 919-3119 FAX: (732) 751-5778 www.dialight.comX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for LED Light Pipes category: Click to view products by Dialight manufacturer: Other Similar products are found below : 1367627-1 SLP3-300-450-F SLP3-400-450-R LPA-C011301S-23 LPA-C011301S-6 LPF-C011306S FLP25-1.95 VLP-640-F LPA- C011301S-5.4 LPA-C041301S-2 LPA-R051171S-12 LPA-S011331S 515-1027-803F 515-1217F SLP3-150-300-R SLP3-500-450-R 515- 1064-810F FLPV-SG BDL-1187 7511A41 7511A87-500 FLPV-SBC 5151064802F 5151-192-0055-0DF LPF-R011340S 515-1166-801F FLPF-6.0 SLP3-350-200-F PM4-C1522-3.70 LC-11.25 CLP-1214 515-1064-808F FLX3 05 515-1192-0025-0DF 515-1192-80-3DF PBLP- 1001-1 LC2-4.1 LPC062CTP LSS024CTP LPC088CTP SLP3-150-300-F 2202312 515-1302-0500F RLP1-200-800 RLP1-400-500 LPA- C011301S-15 2202311 SLP3-150-450-R 7511A53 1270.1003