58113-5

Instruction Sheet 408-9020 Extraction Tool 58113- 29 JUL 10 Rev B 2. Remove the extraction tool, then insert the tip (as previously described) into the opposite side of the assembly, then gently lift the handle until Handle that side of the device is raised from the socket. 3. Repeat this process for the remaining sides of the assembly until the device is released from the socket. Tip 4. TOOL INSPECTION Inspect the tool immediately upon arrival and at regularly scheduled intervals according to Figure 3 to ensure that the tool is not damaged. Figure 1 0.51 .020 76.2 .30 1. INTRODUCTION Extraction Tool 58113- is used to extract a pin grid array (PGA) substrate package (device) from a low insertion force (LIF) PGA socket installed onto a A printed circuit (pc) board. Read these instructions 81.3 3.20 B thoroughly before extracting any devices. C Dimensions in this instruction sheet are in NOTE millimeters with inches in brackets . Figures are not drawn to scale. i Reasons for reissue of this instruction sheet are DIMENSION NUMBER TOOL provided in Section 6, REVISION SUMMARY. OF BLADES A B Typ C Typ 2. DESCRIPTION 58113-1 05 011.7 .46 Each tool features a handle and a tip with blades. See 58113-3 10 024.4 .96 1.52 .060 2.54 .100 Figure 1. 58113-4 13 32.0 1.26 58113-5 16 39.6 1.56 3. USING THE TOOL (Refer to Figure 2) Figure 3 Make sure that all power to the system isOF CAUTION before using the tool. 5. REPLACEMENT The extraction tool cannot be repaired. Order 1. Insert the tip of the extraction tool (with the end replacement tools through your representative, or call of the handle above the socket) between the 1-800-526-5142, or send a facsimile of your purchase device and socket, then gently lift the handle until order to 717-986-7605, or write to: that side of the device is raised from the socket. CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION Lift Tool Handle PO BOX 3608 HARRISBURG PA 17105-3608 Device Tip of Tool 6. REVISION SUMMARY Socket PC Board Revisions to this instruction sheet include: Updated instruction sheet to corporate requirements Figure 2 2010 Tyco Electronics Corporation, Berwyn, PA This controlled document is subject to change. TOOLING ASSISTANCE CENTER 1-800-722-1111 1 of 1 All Rights Reserved For latest revision and Regional Customer Service, PRODUCT INFORMATION 1-800-522-6752 TE logo and Tyco Electronics are trademarks. visit our website at www.tycoelectronics.com *Trademark. Other products, logos, and company names might be trademarks of their respective owners. LOC BX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Extraction, Removal & Insertion Tools category: Click to view products by TE Connectivity manufacturer: Other Similar products are found below : M8196914-08 768211-2 809-131 844751-2 8-59558-2 91018-1 12014013 12093647 1-21048-0 R282867020 12093078 1-21048-6 12121897 DCF.91.405.5LT 1322 15314260 15350698 15350707 15430130 1579018-4 1643916-1 1-679532-0 1976593-3 OUTEXT-0321 2-1579008-3 2-1579008-4 229694-7 231106-1 241469 91040-3 91040-7 965004-000 965069-000 1738219-1 ET-JL05-16 FG 0300 146 3000 FIT-6 210S048 2-1579007-9 231879-1 312138-3 RJ11FODE 356-162 M8196914-10 4-1579018-0 430395-001 483249-1 5- 1579007-2 5-1579007-9 BPR10