Instruction Sheet SDE Hex Crimp 408-32122 Die Set 2217611-1 13 JAN 14 Rev A PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available. PRO-CRIMPER* III Frame Assembly 354940-1 Die Retaining Crimper Die Screws with (Stationary) Tool Frame Crimping Die Assembly 2217611-1 Anvil Die (Movable) The PRO-CRIMPER* III Hand Crimping Tool is a Commercial grade tool and is designed primarily for field installation, repair, maintenance work, or prototyping in industrial, commercial, or institutional applications. Product crimped with this tool will meet the crimp height requirement for hand tools in the appropriate Application Specification (114-series), but may not comply with other feature parameters of the specification. TE Connectivity offers a variety of tools to satisfy your performance requirements. For additional information, contact the Tooling Assistance Center at 1-800-722-1111. Figure 1 1. INTRODUCTION (Figure 1) 2. DESCRIPTION (Figure 2) This instruction sheet provides application and The die assembly features an anvil die and a crimper maintenance procedures for SDE die set 2217611-1. die. When closed, the dies produce three crimping Figure 1 shows PRO-CRIMPER* III hand tool frame chambers that crimp the ferrule of the connector. (354940-1). See the last page of this document for Each die is held in the tool jaws with a single die- other available compatible tooling frames and related retaining screw. instruction sheets to be used with this die set. 3. DIE INSTALLATION (Figure 2) For information on connector part numbers and connector assembly procedures, refer to the 1. Close the tool handles until the ratchet appropriate instruction sheet packaged with the releases then allow the tool handles to open connector. FULLY. NOTE 2. Install anvil die in the moving jaw of the hand Dimensions in this instruction sheet are in metric units tool. Align the die with the retaining screw with U.S. customary units in brackets . Figures and hole then secure die with the button head illustrations are for reference only and are not drawn to cap screw. Do NOT fully tighten. scale. 3. Install crimper die in the stationary jaw of the Read these instructions and all referenced materials hand tool. Slowly close the tool handles, thoroughly before using the die and tool assembly. allowing the die to align itself with the upper die. When dies are properly aligned, securely tighten both screws. 2014 TE Connectivity Ltd. family of companies TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. 1 of 4 All Rights Reserved PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, *Trademark visit our website at www.te.com. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. ORIGINAL INSTRUCTIONS 408-32122 Stationary Jaws Ratchet Crimper Die (Stationary) Die Retaining Screws Anvil Die (Movable) Moving Jaw Figure 2 2. Make sure that the proper die retaining 4. CRIMPING PROCEDURE (Figure 3) screws and die components are properly secured. Prepare connector and cable according to the instructions packaged with the connector, and proceed as follows: Ratchet 1. Close the tool handles until the ratchet releases, then allow the handles to open FULLY. 2. Place connector in the appropriate crimping section of dies as shown in Figure 3. 3. Close the tool handles until the ratchet releases then open the tool handles to remove the crimped connector. 5. MAINTENANCE AND INSPECTION 5.1. Maintenance Cable 1. Remove dust, moisture, and other contaminants with a clean, soft brush, or a clean, soft, lint-free cloth. Do NOT use any Figure 3 objects that could damage the dies or tool. 2. Make sure that the proper die-retaining 3. Inspect the crimping surfaces for flattened, screws are properly secured. chipped, worn, or cracked areas. If damage is evident, the dies must be replaced. Refer 3. When the dies are not in use, store them in a to Section 6, REPLACEMENT. clean, dry area. 5.3. Measuring Die Opening 4. Store the tool with the tool handles closed to prevent objects from becoming lodged within The die assembly will perform correctly as long as: the jaws. (1) the product specified is correct for the application, (2) the specific die assembly is used, (3) the die 5.2. Inspection assembly has been measured to ensure that the openings are correct, and (4) the tool has been 1. Remove all lubrication and accumulated film adjusted correctly. Figure 5 provides information on from the dies by immersing the dies in a die openings. suitable commercial degreaser. 2 of 4 Rev A