MTPSRBCL-C

TX6 PLUS Modular Plug T568B & T568A Part Number: SP688-C Panduit Corp. 2015 INSTALLATION INSTRUCTIONS PN295K T568B Wiring Scheme (Cable end 2) 8 7 6 5 4 3 2 1 Pin BRN/ BLU/ GRN/ ORG/ (Cable end 1) T568B BRN GRN BLU ORG WHT WHT WHT WHT Specifications Strain Relief Boot (MTPSRBCL-C) Cable jacket diameter 0.225-0.250 in. 23-24 AWG stranded or solid conductor Strain Relief Collar (MTX6UTPSRC-C) max. insulated diameter 0.036-0.042 in. Panduit recommends T568B wiring scheme Divider (MTPCD-C) for use with cable constructed with the Load Bar (MTX6PLB-C) brown pair opposing the orange pair. Plug Housing (RTPSA-C) Load Bar Divider Conductor holes and Contact slots Conductor slots and V channel Pins 1 8 Conductor holes V channel Contact slots Divider post CWST Thread boot and collar onto cable. 1 Thread on boot Remove 1.5 of the outer jacket using wire stripping tool and collar first (CJAST). (Cable ends 1 & 2) Fan twisted pairs into respective quadrants. The brown pair should be opposite the orange pair. Cut spline flush to fanned pairs using wire snipping tool (CWST). 90 (Cable end 2) Align the conductor divider V channel with the green pair. 2 BLU (Cable end 1) Insert divider posts into the cable. If the cable has an internal GRN spline, insert divider posts into the brown and orange ORG quadrants of the spline. V channel ORG V channel GRN BRN BRN BLU Arrange conductors to T568B wiring scheme while 3 minimizing untwist. Seat conductors into proper divider slots while holding divider flush with cable jacket. V channel (Cable end 1) (Cable end 2) For Technical Support: www.panduit.com/resources/install maintain.asp Page 1 of 4 Panduit Corp. 2015 INSTALLATION INSTRUCTIONS PN295K Straighten and align untwisted conductors using a circular 4 motion while holding conductors in respective divider slots. Maintain grip of conductors in T568B wiring scheme. Trim conductors on an angle approximately 1.00 from divider leading edge. Pin 8 7 6 5 4 3 2 1 BRN/ BLU/ GRN/ ORG/ T568B BRN GRN BLU ORG WHT WHT WHT WHT 1.00 (Cable end 1) Orient load bar with contact slots facing downward. 5 (Cable end 2) Verify (Cable end 1) load bar orientation 1 8 Pins 1 8 Pins Guide conductors into load bar holes while holding 6 7 conductors in the divider. Slide load bar towards divider until flush. Ensure the divider/load bar is centered and perpendicular to the cable axis. Trim conductors flush with load bar face. (Cable end 1) (Cable end 2) Hold the load bar and divider stationary while sliding the 8 strain relief collar forward until there is no gap between the Collar barbs collar and divider. Confirm the cable jacket extends beyond the collar barbs. Align pin 1 of cable sub-assembly (cable, load bar, divider, Boot position and strain relief collar) with pin 1 of plug housing. when using CSPT 1 8 Pins (Cable end 1) 1 8 Pins MPT5-8AS Grip the strain relief collar and insert cable sub-assembly into 10 9 the plug housing. (Fig. 9) Push sub-assembly into housing until collar locking tabs engage the plug housing pocket. Although not required, TX6 PLUS Plug Assembly Tool (CSPT) is available to facilitate this Plug step. ousing Use tool MPT5-8AS to complete plug termination. (Fig. 10) Push up boot and engage with collar latches. Visually check plug. Assembly is complete. For Technical Support: www.panduit.com/resources/install maintain.asp Page 2 of 4