Z-15G-B7 SEV+

General-purpose Basic Switch Z CSM Z DS E 4 4 Best-selling Basic Switch Boasting High Precision and Wide Variety A large switching capacity of 15 A with high repeat accuracy. A wide range of variations in contact form for your selection: basic, split-contact, maintained-contact, and adjustable contact gap types. A series of standard models for micro loads is available. A series of molded terminal-type models incorporating safety terminal protective cover is available. Be sure to read Safety Precautions on page 26 and Safety Precautions for All Basic Switches. For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Model Number Structure Configuration Refer to page 3. Basic models General-purpose Refer to page 5. Drip-proof Without terminal protective cover Refer to page 5. With terminal protective cover Refer to page 2. Molded terminal Refer to page 4. Split-contact models General-purpose Refer to page 4. Maintained-contact models General-purpose Basic Models Split-contact Models This type is identical in construction to the general-purpose basic General-purpose switch except that it has two pairs of simultaneous acting contacts A variety of actuators is available for a wide range of application. by splitting moving contacts. The contact mechanism of models for micro loads is a crossbar Since the moving contacts are connected to a common terminal, type with gold-alloy contacts, which ensures highly reliable either parallel or series connection is possible. operations for micro loads. Highly reliable micro load switching is ensured if the model is used Contact Gap: as a twin-contact switch. H2: 0.20 mm (extra-high-sensitivity) H: 0.25 mm (high-sensitivity, micro voltage current load) Maintained-contact Models G: 0.5 mm (standard) E: 1.8 mm (high-capacity) The maintained-contact type has a reset button at the bottom of the switch case, in addition to the pushbutton (plunger) located on the Drip-proof opposite side of the reset button. Use these buttons alternately. Since the Switch has greater pretravel than overtravel, it is suitable These Switches use a rubber boot on the actuator and adhesive fill for use in reversible control circuits, manual reset circuits, safety between the case and cover to increase resistance to drips. limit circuits, and other circuits which are not preferable for Models with drip-proof terminal protective covers and molded automatic resetting. (For further details, refer to individual terminals with resin filling are also available. datasheets.) 1Z Model Number Legend Basic Models Standard Models (Drip-proof Type/Molded Terminals) Z- - Z- 55-M M (1)(2)(3)(4) (5) (1) (2)(3) (4) (1) Ratings (1) Drip-proof Type 01 : 0.1 A (micro load) (2) Lead Outlets 15 : 15 A None : VSF (2) Contact Gap 19 : VCT H2 : 0.20 (extra-high-sensitivity) (3) Directions of Lead H : 0.25 mm (high-sensitivity, L Type D Type R Type Outlets (See following micro load) diagrams.) G : 0.5 mm (standard) E : 1.8 mm (high-capacity) L:Left (3) Actuator R : Right D : Descending None : Pin plunger (4) Length of Lead S : Slim spring plunger D : Short spring plunger Outlets K : Spring plunger (medium OP) 1: 1 m K3 : Spring plunger (high OP) 3: 3 m Q3 : Panel mount plunger (low OP) Q : Panel mount plunger (medium Split-contact Models Maintained-contact Models OP) Q8 : Panel mount plunger (high OP) Z-10F Y-B Z-15-E R Q22 : Panel mount roller plunger (1) (2)(3)(4) (5) (1) (2)(3)(4) Q21 : Panel mount cross roller (1) Ratings (1) Ratings plunger L : Leaf spring (high OF) 10 : 10 A (split-contact models) 15 : 15 A L2 : Roller leaf spring (2) Contact Gap (2) Contact Gap W21 : Short hinge lever F : 1 mm (high-capacity) E : 1.8 mm (high capacity) W : Hinge lever (low OF) (3) Actuator (3) Actuator W3 : Hinge lever (medium OF) None : Pin plunger None : Pin plunger W32 : Hinge lever (high OF) S : Slim spring plunger S : Slim spring plunger W4 : Low-force hinge lever D : Short spring plunger W : Hinge lever W44 : Long hinge lever Q : Panel mount plunger (4) Structure W78 : Low-force wire hinge lever Q22 : Panel mount roller plunger R : Maintained-contact models (low OF) W : Hinge lever W52 : Low-force wire hinge lever W22 : Short hinge roller lever (high OF) W2 : Hinge roller lever W22 : Short hinge roller lever M22 : Reverse short hinge roller W2 : Hinge roller lever lever W25 : Hinge roller lever (large roller) (4) Construction W49 : Short hinge cross roller lever Y : Split-contact models W54 : Hinge cross roller lever (5) Terminals W2277 : Unidirectional short hinge roller lever (low OF) B : Screw terminal M : Reverse hinge lever (with toothed washer) M22 : Reverse short hinge roller lever M2 : Reverse hinge roller lever NJ : Flexible rod (high OF) NJS : Flexible rod (low OF) (4) Degree of Protection None : General-purpose 55 : Drip-proof (not include the terminals) A55 : Drip-proof (including the terminals) (5) Terminals None : Solder terminal B : Screw terminal (with toothed washer) B5V : Screw terminal with terminal cover (for Z-15G A55 only) Note: For combinations of models, Ordering Information on page 3 to 6. 2