PCA9560PW,112

PCA9560 2 Dual 5-bit multiplexed 1-bit latched I C-bus EEPROM DIP switch Rev. 5.0 2 December 2021 Product data sheet 1 General description PCA9560 is a 20-pin CMOS device consisting of two 6-bit non-volatile EEPROM registers, 5 hardware pin inputs and a 5-bit multiplexed output with one latched EEPROM bit. It is used for DIP switch-free or jumper-less system configuration and supports Mobile and Desktop VID Configuration, where 3 preset values (2 sets of internal non-volatile registers and 1 set of external hardware pins) set processor voltage for operation in either performance, deep sleep or deeper sleep modes. The PCA9560 is also useful in server and telecom/networking applications when used to replace DIP switches or jumpers, since the settings can be easily changed via I2C/SMBus without having to power down the equipment to open the cabinet. The non-volatile memory retains the most current setting selected before the power is turned off. The PCA9560 typically resides between the CPU and Voltage Regulator Module (VRM) when used for CPU VID (Voltage IDentification code) configuration. It is used to bypass the CPU-defined VID values and provide a different set of VID values to the VRM, if an increase in the CPU voltage is desired. An increase in CPU voltage combined with an increase in CPU frequency leads to a performance boost of up to 7.5%. Lower CPU voltage reduces power consumption. The main advantage of the PCA9560 over the older PCA9559 device in this application is that it contains two internal non-volatile EEPROM registers instead of just one, allowing three independent settings (performance operation, deep sleep mode and deeper sleep mode) instead of only two (performance operation and deep sleep mode). The PCA9560 is footprint compatible and a drop-in replacement for the PCA9559, without any software modifications required. 2 The PCA9560 has 2 address pins allow up to 4 devices to be placed on the same I C- bus or SMBus. 2 Features and benefits 5-bit 3-to-1 multiplexer, 1-bit latch DIP switch 5-bit external hardware pins Two 6-bit internal non-volatile registers, fully pin-to-pin compatible with PCA9559 Selection between the two non-volatile registers Selection between non-volatile registers and external hardware pins 2 I C/SMBus interface logic Internal pull-up resistors on input pin and control signals Active high write protect on input controls the ability to write to the non-volatile registers 2 2 address pins, allowing up to 4 devices on the I C-bus 5 open drain multiplexed outputs Open drain non-multiplexed output 2 Internal 6-bit non-volatile registers programmable and readable via I C-bus 2 External hardware 5-bit value readable via I C-bus 2 Multiplexer selection can be overridden by I C-busNXP Semiconductors PCA9560 2 Dual 5-bit multiplexed 1-bit latched I C-bus EEPROM DIP switch Operating power supply voltage 3.0 V to 3.6 V 5 V and 2.5 V tolerant inputs/outputs 0 to 400 kHz clock frequency ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101 Latch-up testing is done to JESDEC Standard JESD78 which exceeds 100 mA. Offered in TSSOP20 package 3 Ordering information Table 1.Ordering information Type number Topside Package marking Name Description Version PCA9560PW PCA9560 TSSOP20 plastic thin shrink small outline package 20 leads body SOT360-1 width 4.4 mm 3.1 Ordering options Table 2.Ordering options Type number Orderable part Package Packing method Minimum order Temperature number quantity PCA9560PW PCA9560PW,118 TSSOP20 REEL 13 Q1 NDP 2500 T = -40 C to +85 C amb PCA9560 All information provided in this document is subject to legal disclaimers. NXP B.V. 2021. All rights reserved. Product data sheet Rev. 5.0 2 December 2021 2 / 26