DLP11TB800UL2B

Reference Only Spec No. JEFL243E-0011G-01 P1/9 Chip Common Mode Choke Coil DLP11TB800UL2 Reference Specification 1.Scope This reference specification applies to Chip Common Mode Choke Coil DLP11TB series. 2.Part Numbering (ex.) DL P 11 T B 800 U L 2 L (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) Chip Common Mode Choke Coil (6) Common mode Impedance (Typ. at 100MHz) (2) Structure (P : Film Type) (7) Circuit U : Characteristic Impedance 90 system (3) Dimension (LW) (8) Features (4) Magnetic Shield Type (9) Number of Line Thickness (height) 0.3mm (10) Packaging Code L : Taping / B : Bulk (5) Category: Cut off Frequency 8GHz(Typ.) 3.Rating Differential Common Impedance mode to Mode Impedance Characteristics common mode Rated Withstanding Customer Rated DC Insulation Murata Part Number (at 100MHz, between signal lines conversion Voltage Voltage Part Number Current Resistance Resistance Under Standard Z0 characteristic V(DC) V(DC) Testing Condition) (TDR 50ps) (Scd21) 2.5GHz DLP11TB800UL2L 90 -40dB 100M 80+/-25% 5 12.5 100mA 1.5+/-25% +/-15 (typ.) min. DLP11TB800UL2B Operating Temperature : -40 to +85C Storage Temperature : -40 to +85C 4. Standard Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature 15 to 35C Temperature : 20 2C Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to106kPa 5.Style and Dimensions Equivalent Circuits (1) (2) (1) (2) (Top View) (3) (4) 0.10 0.30 (3) (4) No polarity (Side View) Unit Mass (Typical value) :Electrode (Bottom View) 0.002g (in : mm) 0.25 +0.10/ - 0.05 0.10 1.25 6.Marking No Marking. MURATA MFG.CO.,LTD 1.00 0.10 0.55 0.10 0.3 0.05 Reference Only Spec No. JEFL243E-0011G-01 P2/9 7. Electrical Performance No. Item Specification Test Method Common Mode Meet item 3. Measuring Frequency : 1001MHz (ref.item 10.) 7.1 Impedance Measuring Equipment : KEYSIGHT 4291A or the equivalents (In case of doubt, the heat treatment (200C,about 10 minutes)shall be applied. Withstanding Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage 7.2 Voltage Time : 1 to 5 seconds Charge Current : 1 mA max.(ref.item 10.) DC Resistance Meet item 3. Measuring current : 100mA max.(ref.item 10.) 7.3 (Rdc) Insulation Resistance Measuring voltage : Rated Voltage 7.4 (I.R.) Measuring time : 1 minute max. (ref.item 10.) Impedance Network Analyzer 7.5 Characteristics Measuring Equipment : E5071B or the between signal lines (Z0) equivalents (ref.item 10.) Differential mode to Network Analyzer 7.6 common mode conversion Measuring Equipment : E5071B or the characteristics (Scd21) equivalents (ref.item 10.) 8.Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Calipers. Dimensions 8.2 Solderability The electrodes shall be at least Flux : Ethanol solution of rosin,25(wt)% 95% covered with new solder Pre-Heating : 150C, 1minute coating. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 2453C Immersion Time : 31 s Immersion and emersion rates : 25 mm / s 8.3 Resistance to Meet Table 1. Flux : Ethanol solution of rosin,25(wt)% Soldering Heat Table 1 Pre-Heating : 150C ,1minute Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 2705C Common Mode Immersion Time : 101 s Impedance within 20% Immersion and emersion rates : 25 mm / s Change Then measured arter exposure in the room condition I.R. 100M min. for 4 to 48 hours. 8.4 Drop It shall be dropped on concrete or steel board. DC Resistance within 30% Method : free fall Change Height : 1m The Number of Times : 3 times 8.5 Vibration It shall be soldered on the substrate. Oscillation Frequency : 10 to 55 to 10Hz for 1 minute Total Amplitude : 1.5mm Testing Time : A period of 2 hours in each of 3 mutually perpendicular directions. 8.6 Bending Meet Table 2. Substrate : (t =1.0 mm). Strength Table 2 Deflection : 2 mm Speed of Applying Force : 0.5 mm / s Appearance No damaged Keeping time : 30 s Pressure jig DC Resistance within 30% Change R230 F Deflection 45 45 Product MURATA MFG.CO.,LTD