MP44011HS-LF

MP44011 Boundary-Mode PFC Controller with Harmonic Injection The Future of Analog IC Technology DESCRIPTION FEATURES The MP44011 is a boundary-conductionmode Boundary-ConductionMode PFC Controller PFC controller with an internal-harmonic for Pre-Regulation injection function. It provides simple and high- Reduced Bus Capacitance performance active power-factor correction with Reduced Transformer Size minimal external components. Internal Harmonic-Injection Function Precise Adjustable-Output Over-Voltage Compared against traditional boundary- Protection conductionmode PFC controllers, the Ultra-Low Start-Up Current harmonic-injection function makes the part Very Low Quiescent Current suitable for LED lighting applications. On-Chip Filter for Current-Sense Pin In LED lighting applications with two-stage Disable Function structures, the harmonic-injection function can Available in SOIC-8 effectively reduce bus capacitance between the AC/DC and the DC/DC stage. In addition, APPLICATIONS harmonic injection can reduce the transformer LED Lighting Driver size to save board space and BOM cost. General PFC Pre-Regulators Also, the benefits of a harmonic-injection For MPS green status, please visit MPS website under Quality Assurance. function also apply to general boost or flyback MPS and The Future of Analog IC Technology are Registered Trademarks of Monolithic Power Systems, Inc. PFC applications. Patents pending. The MP44011 is derived from the MP44010, except with a harmonic-injection function. The MP44011 is available in an 8-pin SOIC package. TYPICAL APPLICATION C5 D1 Vbus T1 R9 C4 C6 DC/DC D3 R3 D1 D2 R1 R7 C1 R5 C3 V R8 AC R4 R6 U1 ZCS COMP FB R10 VIN MP44011 GATE Q1 MULT GND CS Feedback Network R2 C2 R11 MP44011 Rev. 1.01 www.MonolithicPower.com 1 1/12/2012 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2012 MPS. All Rights Reserved. MP44011 BOUNDARY-MODE PFC CONTROLLER WITH HARMONIC INJECTION ORDERING INFORMATION Part Number Package Top Marking Junction Temperature (T ) J SOIC8 MP44011HS* MP44011 -40C to +125C * For Tape & Reel, add suffix Z (e.g. MP44011HSZ). For RoHS compliant packaging, add suffix LF (e.g. MP44011HSLFZ). PACKAGE REFERENCE TOP VIEW FB 1 8 VIN COMP 2 7 GATE MULT 3 6 GND CS 4 5 ZCS (1) (4) ABSOLUTE MAXIMUM RATINGS Thermal Resistance JA JC Supply Voltage (V ) ...................... -0.5V to +23V SOIC8 ..................................... 90 ...... 45 ... C/W IN Analog Inputs and Outputs .......... -0.3V to +6.5V Notes: ZCS Maximum Current ............ -50mA to +10mA 1) Exceeding these ratings may damage the device. (2) 2) The maximum allowable power dissipation is a function of the Power Dissipation (T =25C) A maximum junction temperature T(MAX), the junction-to- J SOIC8 ........................................................ 1.4W ambient thermal resistance , and the ambient temperature JA Junction Temperature..150C T . The maximum allowable continuous power dissipation at A any ambient temperature is calculated by D(MAX)=(T (MAX)- J Lead Temperature (Solder)....................... 260C T )/ . Exceeding the maximum allowable power dissipation A JA Storage Temperature ............... -55C to +150C will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry (3) Recommended Operating Conditions protects the device from permanent damage. 3) The device is not guaranteed to function outside of its Supply Voltage (V ) ....................... 13.4V to 22V IN operating conditions. Analog Inputs and Outputs ............. -0.3V to +6V 4) Measured on JESD51-7, 4-layer PCB. Operating Junction Temp. (T ). -40C to +125C J MP44011 Rev. 1.01 www.MonolithicPower.com 2 1/12/2012 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2012 MPS. All Rights Reserved.