MP1475DJ-LF-P

MP1475 High-Efficiency, 3A, 16V, 500kHz Synchronous, Step-Down Converter The Future of Analog IC Technology DESCRIPTION FEATURES The MP1475 is a high-frequency, synchronous, Wide 4.5V-to-16V Operating Input Range rectified, step-down, switch-mode converter 80m /30m Low R Internal Power DS(ON) with built-in power MOSFETs. It offers a very MOSFETs compact solution to achieve a 3A continuous High-Efficiency Synchronous Mode output current with excellent load and line Operation regulation over a wide input supply range. The Fixed 500kHz Switching Frequency MP1475 has synchronous mode operation for Synchronizes from a 200kHz-to-2MHz higher efficiency over the output current load External Clock range. Power-Save Mode at light load Current-mode operation provides fast transient Internal Soft-Start response and eases loop stabilization. Power Good Indicator OCP Protection and Hiccup Full protection features include over-current Thermal Shutdown protection and thermal shut down. Output Adjustable from 0.8V The MP1475 requires a minimal number of Available in an 8-pin TSOT-23 Package readily-available standard external components, and is available in a space-saving 8-pin APPLICATIONS TSOT23 package. Notebook Systems and I/O Power Digital Set-Top Boxes Flat-Panel Television and Monitors Distributed Power Systems All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Quality Assurance. MPS and The Future of Analog IC Technology are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION MP1475 Rev. 1.01 www.MonolithicPower.com 1 4/3/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2014 MPS. All Rights Reserved. NOT RECOMMENDED FOR NEW DESIGNS REFER TO MP2333MP1475 SYNCHRONOUS STEP-DOWN CONVERTER ORDERING INFORMATION Part Number* Package Top Marking MP1475DJ TSOT-23-8 ADP * For Tape & Reel, add suffix Z (e.g. MP1475DJZ) For RoHS Compliant Packaging, add suffix LF (e.g. MP1475DJLFZ) PACKAGE REFERENCE TOP VIEW PG 1 8 FB IN 2 7 VCC SW EN/SYNC 3 6 GND BST 4 5 (1) (5) ABSOLUTE MAXIMUM RATINGS Thermal Resistance JA JC V ................................................ -0.3V to 17V TSOT-23-8............................ 100..... 55... C/W IN V .................................................................... SW Notes: -0.3V (-5V for <10ns) to 17V (19V for <10ns) 1) Exceeding these ratings may damage the device. V ...................................................... V +6V 2) About the details of EN pins ABS MAX rating, please refer to BST SW (2) Page 9, Enable/SYNC control section. All Other Pins................................-0.3V to 6V 3) The maximum allowable power dissipation is a function of the (3) Continuous Power Dissipation (T = +25C) maximum junction temperature T (MAX), the junction-to- A J ambient thermal resistance , and the ambient temperature JA ..........................................................1.25W T . The maximum allowable continuous power dissipation at A Junction Temperature..............................150C any ambient temperature is calculated by P (MAX) = (T D J (MAX)-T )/ . Exceeding the maximum allowable power A JA Lead Temperature ...................................260C dissipation will cause excessive die temperature, and the Storage Temperature................. -65C to 150C regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent (4) Recommended Operating Conditions damage. 4) The device is not guaranteed to function outside of its Supply Voltage V .......................... 4.5V to 16V IN operating conditions. Output Voltage V ...............0.8V to V x D OUT IN MAX 5) Measured on JESD51-7, 4-layer PCB. Operating Junction Temp. (T ). -40C to +125C J MP1475 Rev. 1.01 www.MonolithicPower.com 2 4/3/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2014 MPS. All Rights Reserved. NOT RECOMMENDED FOR NEW DESIGNS REFER TO MP2333