SY100EL32VZG

SY100EL32V 5V/3.3V ECL 2 Divider Features General Description 3.3V and 5V Power Supply Options The SY100EL32V is an integrated 2 divider. The differential clock inputs and the VBB allow a differential, 510 ps Propogation Delay (Typical) single-ended or AC-coupled interface to the device. If 3.0 GHz Toggle Frequency (Typical) used, the VBB output should be bypassed to ground High Bandwidth Output Transitions with a 0.01 F capacitor. Also note that the VBB is Internal 75 k Input Pull-Down Resistors designed to be used as an input bias on the EL32V Available in 8-Lead SOIC Package only the VBB output has limited current sink and source capability. The RESET pin is asynchronous and is asserted on the rising edge. Upon power-on, the internal flip-flop will attain a random state. The RESET allows for the synchronization of multiple EL32Vs in a system. Package Type SY100EL32V 8-Lead SOIC (Z) VCC RESET 1 8 R CLK 2 7 Q 2 /CLK 3 6 /Q VBB VEE 4 5 2018-2019 Microchip Technology Inc. DS20006083B-page 1SY100EL32V 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings PECL Power Supply Voltage (V ) (Note 1).............................................................................................................. +8V CC NECL Power Supply Voltage (V ) (Note 2).............................................................................................................. 8V EE PECL Mode Input Voltage (V ) (Note 3) ................................................................................................................... +6V IN NECL Mode Input Voltage (V ) (Note 4)................................................................................................................... 6V IN Continuous Output Current (I ).......................................................................................................................... 50 mA OUT Surge Output Current (I ) ................................................................................................................................ 100 mA OUT Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the Notice: device. Exposure to maximum rating conditions for extended periods may affect device reliability. = 0V. Note 1: V EE = 0V. 2: V CC = 0V, V V . 3: V EE IN CC = 0V, V V . 4: V CC IN EE PECL DC ELECTRICAL CHARACTERISTICS Electrical Characteristics PECL: V = 3.0V to 5.5V V = 0V T = 40C to +85C, unless otherwise stated. ( Note 1) CC EE A Parameter Symbol Min. Typ. Max. Units Conditions 25 30 T = 40C to +25C A Power Supply Current I mA EE = +85C 29 35 T A V 1.085 V 1.005 V 0.88 T = 40C CC CC CC A Output High Voltage (Note 2) V V OH 1.025 V 0.955 V 0.88 T = 0C to +85C V CC CC CC A V 1.830 V 1.695 V 1.555 T = 40C CC CC CC A Output Low Voltage (Note 2) V V OL 1.810 V 1.705 V 1.620 T = 0C to +85C V CC CC CC A V 1.38 V 1.26 V Output Reference Voltage V BB CC CC Input High Voltage V V 1.165 V 0.880 V IH CC CC (Single-Ended) Input Low Voltage V V 1.810 V 1.475 V IL CC CC (Single-Ended) 2.0 V 0.4 T = 40C CC A Common Mode Range (Note 3) V V IHCMR 0.4 T = 0C to +85C 1.9 V CC A 150 A Input High Current I IH 0.5 A V = V Input Low Current I IL IN IL(MIN) Note 1: Devices are designed to meet the DC specifications shown in the above table after thermal equilibration has been established. The circuit is in a test socket or mounted on a printed circuit board, and transverse airflow greater than 500 lfpm is maintained. 2: Outputs are terminated through a 50 resistor to V 2.0V. CC 3: The CMR range is referenced to the most positive side of the differential input voltage. Normal operation is obtained if the high level falls within the specified range and the peak-to-peak voltage lies between 150 mV and 1V. 2DS20006083B-page 2018-2019 Microchip Technology Inc.