PIC16LF18854-I/ML

PIC16(L)F18854 Full-Featured 28/40/44-Pin Microcontrollers Description PIC16(L)F18854 microcontrollers feature Analog, Core Independent Peripherals and Communication Peripherals, combined with eXtreme Low-Power (XLP) technology for a wide range of general purpose and low-power applications. The family will feature the CRC/SCAN, Hardware Limit Timer (HLT) and Windowed Watchdog Timer (WWDT) to support customers looking to add safety to their application. Additionally, this family includes up to 7 KB of Flash memory, along 2 with a 10-bit ADC with Computation (ADC ) extensions for automated signal analysis to reduce the complexity of the application. Core Features Power-Saving Functionality C Compiler Optimized RISC Architecture DOZE mode: Ability to run the CPU core slower Only 49 Instructions than the system clock Operating Speed: IDLE mode: Ability to halt CPU core while internal - DC 32 MHz clock input peripherals continue operating - 125 ns minimum instruction cycle Sleep mode: Lowest Power Consumption Interrupt Capability Peripheral Module Disable (PMD): 16-Level Deep Hardware Stack - Ability to disable hardware module to Three 8-Bit Timers (TMR2/4/6) with Hardware minimize power consumption of unused Limit Timer (HLT) Extensions peripherals Four 16-Bit Timers (TMR0/1/3/5) Low-Current Power-on Reset (POR) eXtreme Low-Power (XLP) Features Configurable Power-up Timer (PWRTE) Sleep mode: 50 nA 1.8V, typical Brown-out Reset (BOR) with Fast Recovery Watchdog Timer: 500 nA 1.8V, typical Low-Power BOR (LPBOR) Option Secondary Oscillator: 500 nA 32 kHz Windowed Watchdog Timer (WWDT): Operating Current: - Variable prescaler selection -8 A 32 kHz, 1.8V, typical - Variable window size selection -32 A/MHz 1.8V, typical - All sources configurable in hardware or software Programmable Code Protection Digital Peripherals Four Configurable Logic Cells (CLC): Memory - Integrated combinational and sequential logic Three Complementary Waveform Generators Up to 7 KB Flash Program Memory (CWG): Up to 512B Data SRAM - Rising and falling edge dead-band control 256B of EEPROM - Full-bridge, half-bridge, 1-channel drive Direct, Indirect and Relative Addressing modes - Multiple signal sources Five Capture/Compare/PWM (CCP) module: Operating Characteristics - 16-bit resolution for Capture/Compare modes Operating Voltage Range: - 10-bit resolution for PWM mode - 1.8V to 3.6V (PIC16LF18854) 10-bit PWM: - 2.3V to 5.5V (PIC16F18854) -Two 10-bit PWMs Temperature Range: Numerically Controlled Oscillator (NCO): - Industrial: -40C to 85C - Generates true linear frequency control and - Extended: -40C to 125C increased frequency resolution < 32 MHz - Input Clock: 0 Hz < F NCO 20 - Resolution: F /2 NCO Two Signal Measurement Timers (SMT): - 24-bit Signal Measurement Timer - Up to 12 different Acquisition modes 2016-2018 Microchip Technology Inc. DS40001826C-page 1PIC16(L)F18854 Digital Peripherals (Cont.) Flexible Oscillator Structure Cyclical Redundancy Check (CRC/SCAN): High-Precision Internal Oscillator: - 16-bit CRC - Software selectable frequency range up to 32 - Scans memory for NVM integrity MHz, 1% typical Communication: x2/x4 PLL with Internal and External Sources - EUSART, RS-232, RS-485, LIN compatible Low-Power Internal 32 kHz Oscillator - Two SPI (LFINTOSC) 2 C, SMBus, PMBus compatible -Two I External 32 kHz Crystal Oscillator (SOSC) Up to 25 I/O Pins: External Oscillator Block with: - Individually programmable pull-ups - Three crystal/resonator modes up to 20 MHz - Slew rate control - Three external clock modes up to 20 MHz - Interrupt-on-change with edge-select Fail-Safe Clock Monitor: - Input level selection control (ST or TTL) - Allows for safe shutdown if peripheral clock - Digital open-drain enable stops - Current mode enable Oscillator Start-up Timer (OST) Peripheral Pin Select (PPS): - Ensures stability of crystal oscillator - Enables pin mapping of digital I/O resources Data Signal Modulator (DSM) - Modulates a carrier signal with digital data to create custom carrier synchronized output waveforms Analog Peripherals Analog-to-Digital Converter with Computation 2 (ADC ): - 10-bit with up to 24 external channels - Automated post-processing - Automates math functions on input signals: averaging, filter calculations, oversampling and threshold comparison - Operates in Sleep Two Comparators (COMP): - Fixed Voltage Reference at (non) inverting input(s) - Comparator outputs externally accessible 5-Bit Digital-to-Analog Converter (DAC): - 5-bit resolution, rail-to-rail - Positive Reference Selection - Unbuffered I/O pin output - Internal connections to ADCs and comparators Voltage Reference: - Fixed Voltage Reference with 1.024V, 2.048V and 4.096V output levels 2016-2018 Microchip Technology Inc. DS40001826C-page 2