AT34C02C-TH-B

Features Permanent and reversible software write protection for the first-half of the array Software procedure to verify write protect status Hardware write protection for the entire array Low-voltage and standard-voltage operation 1.7 (V = 1.7V to 5.5V) CC Internally organized 256 x 8 Two-wire serial interface Schmitt trigger, filtered inputs for noise suppression Two-wire Serial Bidirectional data transfer protocol Electrically-erasable 100kHz (1.7V) and 400kHz (2.7V and 5.0V) compatibility 16-byte page write modes and Programmable Partial page writes are allowed Read Only Memory Self-timed write cycle (5ms max) with Permanent High-reliability Endurance: 1 million write cycles and Reversible Data retention: 100 years Software Write 8-lead JEDEC SOIC, 8-lead UDFN, 8-lead TSSOP, and 8-ball VFBGA packages Die sales: wafer form, tape and reel, and bumped wafers Protect 2K (256 x 8) Description The Atmel AT34C02C provides 2048 bits of serial electrically-erasable and programmable Atmel AT34C02C read only memory (EEPROM) organized as 256 words of eight bits each. The first-half of the device incorporates a permanent and a reversible software write protection feature while hardware write protection for the entire array is available via an external pin. Once the Not Recommended for permanent software write protection is enabled, by sending a special command to the device, it cannot be reversed. However, the reversible software write protection is enabled New Design and can be reversed by sending a special command. The hardware write protection is con- trolled with the WP pin and can be used to protect the entire array, whether or not the Replaced by AT34C02D software write protection has been enabled. This allows the user to protect none, first-half, or all of the array depending on the application. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operations are essential. The AT34C02C is available in space saving 8-lead JEDEC SOIC, 8-lead UDFN, 8-lead TSSOP, and 8-ball VFBGA packages and is accessed via a Two-wire serial interface. It is available in 1.7V (1.7V to 5.5V). 8-lead UDFN 8-ball dBGA2 8-lead TSSOP A 1 8 V 0 CC 8 1 V 8 1 A V A 0 CC 0 CC A 2 7 WP 1 WP 7 2 A 7 2 A WP 1 1 A 3 6 SCL 2 SCL 6 3 A 2 SCL 6 3 A 2 GND 4 5 SDA 5 4 SDA GND 5 4 GND SDA 8-lead SOIC Bottom View Bottom View A 1 8 V 0 CC A 2 7 WP 1 A 3 6 SCL 2 GND 4 5 SDA 5185FSEEPROM102014Table 0-1. Pin Configurations Pin Name Function A0 - A2 Address inputs SDA Serial data SCL Serial clock input WP Write protect 1. Absolute Maximum Ratings* *NOTICE: Stresses beyond those listed under Absolute Operating temperature 55C to +125C Maximum Ratings may cause permanent dam- age to the device. This is a stress rating only Storage temperature 65C to +150C and functional operation of the device at these or any other conditions beyond those indicated Voltage on any pin in the operational sections of this specification with respect to ground .1.0V to +7.0V is not implied. Exposure to absolute maximum rating conditions for extended periods may Maximum operating voltage 6.25V affect device reliability. DC output current . 5.0mA Figure 1-1. Block Diagram V CC GND WP START SCL SERIAL STOP CONTROL SDA LOGIC LOGIC EN H.V. PUMP/TIMING WRITE PROTECT CIRCUITRY LOAD COMP DATA RECOVERY DEVICE ADDRESS COMPARATOR SOFTWARE WRITE LOAD INC PROTECTED AREA A (00H - 7FH) 2 A R/W 1 DATA WORD ADDR/COUNTER A 0 EEPROM Y DEC SERIAL MUX D D /ACK IN OUT LOGIC D OUT 2 AT34C02C 5185FSEEPROM102014 X DEC