Product Information

K2970

K2970 electronic component of Endicott

Datasheet
CCFL Inverter Dual Lamp 58KHz 12-Pin

Manufacturer: Endicott
This product is classified as Large/Heavy, additional shipping charges may apply. A customer service representative may contact you after ordering to confirm exact shipping charges



Price (USD)

1: USD 26.02 ea
Line Total: USD 26.02

0 - Global Stock
MOQ: 1  Multiples: 1
Pack Size: 1
Availability Price Quantity
0 - Global Stock


Ships to you between Fri. 05 Apr to Thu. 11 Apr

MOQ : 1
Multiples : 1

Stock Image

K2970
Endicott

1 : USD 26.02

     
Manufacturer
Product Category
LoadingGif

Notes:- Show Stocked Products With Similar Attributes.
Image Description
Image Description
F-596-C electronic component of Waldom F-596-C

4 X 1/2 PAN HEAD SCREW
Stock : 1

RVUVK105CH020BW-F electronic component of Taiyo Yuden RVUVK105CH020BW-F

CAP, HIGH FREQ, 0402, 50V, C0H
Stock : 1

MPZ2012-KIT electronic component of TDK MPZ2012-KIT

C216-005
Stock : 1

RVEVK105CH3R9JW-F electronic component of Taiyo Yuden RVEVK105CH3R9JW-F

CAP, HIGH FREQ, 0402, 16V, C0H
Stock : 1

RMJMK063BJ224MP-F electronic component of Taiyo Yuden RMJMK063BJ224MP-F

CAP 0.22UF 6.3VDC X5R 20% SMD 0201
Stock : 1

RMUMK105CG3R9CV-F electronic component of Taiyo Yuden RMUMK105CG3R9CV-F

CAP, MLCC, 0402, 50V, C0G, 3.9
Stock : 1

OSTOQ025350 electronic component of On Shore Technology OSTOQ025350

Conn Shrouded Header (4 Sides) HDR 2 POS 5.08mm Solder ST Thru-Hole
Stock : 1

F-465-C electronic component of Waldom F-465-C

F465C waldom
Stock : 1

F-524-C electronic component of Waldom F-524-C

F524C waldom
Stock : 1

F-040-C electronic component of Waldom F-040-C

F040C waldom
Stock : 1

1 8 K2970 Specifications and 8m Class8m Class 8m Class8m Class8m Class Applications Information 2 Lamp DC to AC Inverter 02/09/11 8m Class8m Class The ERG K2970 (8m Class8m Class8m Class) low profile dc to ac inverter is specifically designed to power the LG Philips LB104V03 LCD display backlight to a moderate brightness level from a +12 volt dc source. K Series Package PCB components are shown for reference only. This low profile inverter features: Actual product may differ from that shown. Less Than 8 mm in Height Package Configuration LCD Module Specific Display Compatible Output Connector .79[20,1] Firm Specifications J2 1 Application Information Designed, Manufactured and Supported in the USA Output Custom Input and Output Voltages (2X) Flexible System Interface Notebook Display Head Compatible 3.300 [83,82] 4.20 [106,7] Connectors Input Connector Output Connectors Input JST Molex SM02B-BHSS-1-TB 53261-0871 J1 J2-1 ACout J1-1 +Vin J2-2 ACreturn J1-2 +Vin J1-3 GND .47[11,9] J3-1 ACout J1-4 GND J3-2 ACreturn .120[3,05] J1-5 Enable/PWM * Dia. (2x) J1-6 N/C 1 J3 J1-7 N/C J1-8 N/C .450[11,43] .12[3,0] * Valid only with C jumper (JP1) removed page 1 of 3. C PCB components are shown for reference only. Actual product may differ from that shown.K2970 Absolute Maximum Ratings Rlating SeymboVsalu Unit Input Voltage Range -c0.3 to +13.2 Vd V in o Storage Temperature -40 to +85 C T stg Operating Characteristics With a load simulating the referenced display and lamp warm-up of 5 minutes. o Unless otherwise noted Vin = 12.00 Volts dc and Ta = 25 C. Clharacteristic Snymbo Mpi Txy Msa Unit Input Voltage +010.8 +612. +c12. Vd V in Component Surface o --20 +80 C T (note 1) s Temperature (note 2) -807.5 0c.6 Ad I Input Current in Operating Frequency 583 536zkH F o (note 3) 9-40 - Vrms Minimum Output Voltage V (min) out hhhhh Efficiency -48- % Output Current (per lamp) -06-. mArms I out Output Voltage -54-8 Vrms V out Enable Pin Input Current -04-. mAdc I (notes 4,5,6) Enable Requirement Specifications subject to change without notice. (Note 1) Surface temperature must not exceed 80 degrees C; thermal management actions may be required. (Note 2) Input current in excess of maximum may indicate a load/inverter mismatch condition, which can result in reduced reliability. Please contact ERG technical support. (Note 3) Provided data is not tested but guaranteed by design. (Note 4) Required User Enable/Disable Interface Circuit is shown on page 3. (Note 5) Valid only with C jumper (JP1) removed. (Note 6) With the inverter powered and JP1 is in place, a ground applied to the enable pin J1-5 will open the inverter fuse. Application Notes: 1) The minimum distance from high voltage areas of the inverter to any conductive material should be .12 inches per kilovolt of starting voltage. 2) Mounting hardware to be non-conductive. 3) Open framed inverters should not be used in applications at altitudes over 10,000 feet. 4) ACreturn should be left floating, not grounded. 5) Contact ERG for possible exceptions. Made in USA page 2 of 3.

Looking for help? Visit our FAQ's Section to answer to all your questions

 

X-ON Worldwide Electronics

Welcome To X-ON ELECTRONICS
For over three decades, we have been advocating and shaping the electronic components industry. Our management complements our worldwide business scope and focus. We are committed to innovation, backed by a strong business foundation. If you need a trustworthy supplier of electronic components for your business – look no further.
 

Copyright ©2024  X-ON Electronic Services. All rights reserved.
Please ensure you have read and understood our Terms & Conditions before purchasing.
All prices exclude GST.

Image for all the cards that are accepted Image for all the cards that are accepted Image for all the cards that are accepted Image for all the cards that are accepted Image for all the cards that are accepted