CY4541

QUICK START GUIDE TM CY4541 EZ-PD CCG4 EVK Unpack the kit contents STEP 1 USB 3.0 EMCA Type-C Cable USB 3.0 Type-A CCG EVK CY4541 CCG4 CCG EVK USB 2.0 Type-A to Type-B Cables Base Board Base Board Daughter Card to Mini-B Cable Screwdriver Jumper Wire USB Type-C to 24V DC Power Adapter Type-A Adapters Note: Color of the solder mask used on CCG EVK base boards and CY4541 CCG4 daughter card may vary from the image shown in step1. Verify that the user LED jumper (J11) is populated on CCG EVK base board 1 (connected to Port 1of STEP CCG4 daughter card) and that the voltage selection jumper (J5) on the CCG4 daughter card is set to 2 3.3 V (position 1-2). Ensure that the wires are connected with correct polarity between the power provider header (J12) of both the CCG EVK base boards as shown in the gure in step2. Connect the DC power adapter (provided with the kit) to the DC power jack (J1) of either of the CCG EVK base boards.Verify that the setup is as shown in the gure in step2. Plug the other end of the DC power adapter to the AC power socket. LED1 (Green) on the CCG4 daughter card and on both the CCG EVK base boards glow to indicate that the kit is powered. In addition, the LED2 (Orange) on the CCG EVK base board 1 blinks continuously to indicate that CCG4 is powered and active. Red color wire to the CCG CY4541 CCG4 +ve terminal EVK Base Board 1 Daughter Card J12 J1 LED1 CCG EVK Base Board 2 (on CCG4 Daughter Card) LED1(on CCG EVK Base Board 2) Port 1 LED1 (on CCG EVK Base Board 1) LED2 (on CCG EVK Base Board 1) J5 J1 DC Power Adapter Connected to CCG EVK Base Board 1 Note: Ensure that CCG4 daughter J11 card is rmly connected to the Red color wire to the CCG EVK base boards. +ve terminal J12 + +QUICK START GUIDE TM CY4541 EZ-PD CCG4 EVK Connect each USB 3.0 Type-A to Type-B cable from the PC to the USB Type-B port (J2) of each STEP of the CCG EVK base boards. Connect each USB Type-C to Type-A adapter to the USB Type-C 3 port (J3) of each of the CCG EVK base boards. Plug USB pendrives (not provided with the kit) into both the USB Type-C to Type-A adapters. Verify that the setup is as shown in the gure in step3. Observe the enumeration of both the USB pendrives on the PC. Initiate data transfer between the two USB pendrives, and observe the data transfer speed*. This step demonstrates the capability of CCG4 to control two USB Type-C interfaces simultaneously. J2 USB Type-C to USB Type-C to Type-A Adapter Type-A Adapter USB 3.0 Type-A USB Pen-drive to Type-B cable J3 USB Pen-drive J3 connected to CCG EVK J2 Base Board 1 USB 3.0 Type-A to Type-B cable connected to CCG EVK Base Board 2 USB USB USB 3.0 enabled notebook or PC is recommended Note that any USB device can be used instead of a pendrive with the setup shown in step3. * Data transfer speed depends on the type of the USB port (SuperSpeed or High Speed) of the PC, the pendrive (SuperSpeed or High Speed) and the system con guration. Refer to the CY4541 Kit guide** for a detailed explanation of the Dual Role Port (DRP) and STEP Type-C to Display Port demo using CCG4. 4 ** Download and install the CY4541 CCG4 EVK complete setup from www.cypress.com/CY4541 to access the kit design les and documentation. After the installation, CY4541 Kit Guide.pdf will be available at C: Program Files (x86) Cypress CY4541 CCG4 EVK 1.0 Documentation CY4541 Kit Guide.pdf (on 64-bit Windows operating systems) or C: Program Files Cypress CY4541 CCG4 EVK 1.0 Documentation CY4541 Kit Guide.pdf (on 32-bit Windows operating systems) 2016 - 2017 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. 002-10266 Rev.*F