Micrel, Inc. SY88993AV 5V/3.3V 3.2Gbps HIGH-SPEED SY88993AV LIMITING POST AMPLIFIER DESCRIPTION FEATURES > 3.2Gbps operation The SY88993AV limiting post amplifier with its high and wide bandwidth is ideal for use as a post amplifier in fiber- Low noise CML data outputs optic receivers with data rates up to 3.2Gbps. Signals as Chatter-Free LOS generation small as 4mVp-p can be amplified to drive devices with Open Collector TTL LOS output CML inputs or AC coupled PECL inputs. The SY88993AV TTL /EN Input generates a chatter-free Loss of Signal (LOS) open collector TTL output. Differential PECL inputs for data The SY88993AV incorporates a programmble level detect Single 3.3V or 5V power supply function to identify when the input signal has been lost. Designed for use with SY88922V and SY88905 This information can be fed back to the /EN input of the Available in a tiny 10-pin (3mm) MSOP device to maintain stability under loss of signal conditions. Using LOS pin the sensitivity of the level detect can be LVL adjusted. The LOS voltage can be set by connecting a LVL APPLICATIONS resistor divider between V and V , Figure 3. CC REF 1.25Gbps and 2.1Gbps Gigabit Ethernet V CC 531Mbps, 1062Mbps and 2.5Gbps SONET/SDH SY88993AV Fibre Channel 4.7k to 10k LOS 622Mbps Gigabit interface converter (GBIC) Small form factor trancievers Parallel 10G Ethernet BLOCK DIAGRAM D D IN OUT Limiting CML Amplifer Buffer /D /D IN OUT V REF Enable /EN V CC Level GND Detect LOS LOS LVL Rev.: D Amendment: /0 M9999-091207 1 Issue Date: September 2007 hbwhelp micrel.com or (408) 955-1690Micrel, Inc. SY88993AV PACKAGE/ORDERING INFORMATION Ordering Information /EN 1 10 VCC Package Operating Package Lead Part Number Type Range Marking Finish DIN 2 9 DOUT MSOP SY88993AVKI K10-1 Industrial 993A Sn-Pb /DIN 3 8 /DOUT K10-1 (1) SY88993AVKITR K10-1 Industrial 993A Sn-Pb VREF 4 7 LOS SY88993AVKG K10-1 Industrial 993A with Pb-Free LOSLVL 5 6 GND Pb-Free bar-line indicator NiPdAu (1) SY88993AVKGTR K10-1 Industrial 993A with Pb-Free 10-Pin MSOP (K10-1) Pb-Free bar-line indicator NiPdAu Note: 1. Tape and Reel. PIN NAMES GENERAL DESCRIPTION General Pin Type Function The SY88993AV is an integrated limiting amplifier D Data Input Data Input IN intended for high-frequency fiber-optic applications. The /D Data Input Inverting Data Input IN circuit connects to typical transimpedance amplifiers found within a fiber-optics link. The linear signal output from a LOS Input Loss of Signal Level Set LVL transimpedance amplifier can contain significant amounts /EN TTL Input Output Enable (Active Low) of noise, and may vary in amplitude over time. The LOS TTL Output Loss of Signal Indicator SY88993AV limiting amplifier quantizes the signal and (Open Collector) (Active High) outputs a voltage-limited waveform. GND Ground Ground The /EN pin allows the user to disable the output signal without removing the input signal. D CML Output Data Output OUT /D CML Output Inverting Data Output OUT V Power Supply Positive Power Supply CC V Output Reference Voltage Output REF for LOS Level Set (see Fig. 3) (1) ABSOLUTE MAXIMUM RATINGS Symbol Rating Value Unit V Power Supply Voltage 0 to +7.0 V CC D , /D Input Voltage 0 to V V IN IN CC T Operating Temperature Range 40 to +85 C A T Storage Temperature Range 55 to +85 C STORE Note: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. M9999-091207 2 hbwhelp micrel.com or (408) 955-1690